- 您現在的位置：買賣IC網 > PDF目錄9341 > ISL1209IU10 (Intersil)IC RTC/CALENDAR I2C 10-MSOP PDF資料下載
參數資料
| 型號： | ISL1209IU10 |
| 廠商： | Intersil |
| 文件頁數： | 24/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC/CALENDAR I2C 10-MSOP |
| 標準包裝： | 80 |
| 類型： | 時間事件記錄器 |
| 特點： | 警報器，閏年，SRAM |
| 存儲容量： | 2B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
9
FN6109.4
October 17, 2006
Power Mode, is available to allow direct switching from VDD
to VBAT without requiring VDD to drop below VTRIP. Since
the additional monitoring of VDD vs. VTRIP is no longer
needed, that circuitry is shut down and less power is used
while operating from VDD. Power savings are typically
600nA at VDD = 5V. Low Power Mode is activated via the
LPMODE bit in the control and status registers.
Low Power Mode is useful in systems where VDD is normally
higher than VBAT at all times. The device will switch from
VDD to VBAT when VDD drops below VBAT, with about 50mV
of hysteresis to prevent any switchback of VDD after
switchover. In a system with a VDD = 5V and backup lithium
battery of VBAT = 3V, Low Power Mode can be used.
However, it is not recommended to use Low Power Mode in
a system with VDD = 3.3V ±10%, VBAT ≥ 3.0V, and when
there is a finite I-R voltage drop in the VDD line.
InterSeal Battery Saver
The ISL1209 has the InterSeal Battery Saver which
prevents initial battery current drain before it is first used. For
example, battery-backed RTCs are commonly packaged on
a board with a battery connected. In order to preserve
battery life, the ISL1209 will not draw any power from the
battery source until after the device is first powered up from
the VDD source. Thereafter, the device will switchover to
battery backup mode whenever VDD power is lost.
Event/Tamper Monitor and Detection
The ISL1209 provides an event detection and alarm function
to be used in a wide variety of applications ranging from
security, warranty monitoring, data collection and recording.
The tamper detect input pin, EVIN, can be used as a event
or tamper detection input of an external switch (mechanical
or electronic). When the EVIN pin is a valid HIGH, the
ISL1209 sets the EVT bit in the status register and, can
optionally: 1) Issue an Event output signal (EVDET pin),
2) At the time event occurred, stop the RTC registers from
advancing.
To allow for flexibility of external switches used at the EVIN
pin, the internal pull-up (~1A in full on mode) can be
disabled/enabled. This will allow more flexibility depending
on the capacitive and resistive loading at the EVIN pin.
A noise filter option is also provided for the event monitor
circuit. The EVIN pin has a time based filter where the EVIN
signal must be stable for a period of time to trigger a valid
detection. The time hysteresis filter can vary from 0, 3.9ms,
15.2ms or 31.25ms.
For low power applications the event monitor can be
sampled at a user selectable rate. The EVIN pin can be
always ON or periodically sampled with a frequency of 1/4,
1or 2Hz.
Event Detect Timing Diagram With
Sampling Mode Enabled
Case 1, Switched Opened Before Ipu
Case 2, Switched Opened After Ipu
Case 3, Switched Bounced
The ISL1209 can operate independently or in conjunction
with a microcontroller for low power operation modes or in
battery backup modes.
The event detection circuits operate in either main VDD
power or battery backup mode.
8 clks (8x)
15 clks (8x)
OFF
ON
OPEN
CLOSED
LOW
HIGH
LOW
EVDET
EVIN
EXT.
SWITCH
Ipu
8 clks (8x)
15 clks (8x)
OFF
ON
OPEN
CLOSED
LOW
HIGH
LOW
EVDET
EVIN
EXT.
SWITCH
Ipu
15 clks (8x)
OFF
ON
OPEN
CLOSED
LOW
HIGH
LOW
EVDET
EVIN
EXT.
SWITCH
Ipu
8 clks (8x)
ISL1209
相關PDF資料 |
PDF描述 |
|---|---|
| MCP4152-502E/MS | IC POT DGTL SNGL 5K RHEO 8MSOP |
| VE-2NY-MW-F4 | CONVERTER MOD DC/DC 3.3V 66W |
| VE-2NY-MW-F3 | CONVERTER MOD DC/DC 3.3V 66W |
| X1226V8Z | IC RTC/CALENDAR/4K EE 8-TSSOP |
| MS3451L18-13P | CONN RCPT 4POS CBL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL1209IU10-TK | 功能描述:IC RTC/CALENDAR I2C 10-MSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| ISL1209IU10Z | 功能描述:實時時鐘 I2CAL TIME CLK/CLNDR W/EVENT DETCT 10LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1209IU10Z-TK | 功能描述:實時時鐘 I2CAL TIME CLK/CLNDR W/EVENT DETCT 10LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1218 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM |
| ISL1218IBZ | 功能描述:實時時鐘 REAL TIME CLKRTC IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。