- 您現在的位置：買賣IC網 > PDF目錄9068 > ISL22329UFU10Z-TK (Intersil)IC POT DGTL 128TP LN LP 10-MSOP PDF資料下載
參數資料
| 型號： | ISL22329UFU10Z-TK |
| 廠商： | Intersil |
| 文件頁數： | 4/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 128TP LN LP 10-MSOP |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 電阻（歐姆）： | 50k |
| 電路數： | 2 |
| 溫度系數： | 標準值 ±80 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
12
FN6330.2
September 4, 2009
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL22329 responds with an ACK. At this time, the device
enters its standby state (See Figure 14). Device can receive
more than one byte of data by auto incrementing the
address after each received byte. Note after reaching the
address 08h, the internal pointer “rolls over” to address 00h.
Non-volatile write cycle starts after STOP condition is
determined and it requires up to 20ms delay for the next
non-volatile write. Thus, non-volatile registers must be
written individually.
Read Operation
A Read operation consist of a three byte instruction followed
by one or more Data Bytes (See Figure 15). The master
initiates the operation issuing the following sequence: a
START, the Identification byte with the R/W bit set to “0”, an
Address Byte, a second START, and a second Identification
byte with the R/W bit set to “1”. After each of the three bytes,
the ISL22329 responds with an ACK. Then the ISL22329
transmits Data Bytes as long as the master responds with an
ACK during the SCL cycle following the eighth bit of each
byte. The Data Bytes are from the registers indicated by an
internal pointer. This pointer initial value is determined by the
Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 08h, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.The master terminates the read
operation (issuing a ACK and STOP condition) following the
last bit of the last Data Byte (See Figure 15).
The Data Bytes are from the registers indicated by an
internal pointer. This pointer initial value is determined by the
Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 08h, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.
In order to read back the non-volatile IVR, it is recommended
that the application reads the ACR first to verify the WIP bit
is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat
its reading sequence again.
ISL22329
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BT4-MY-F3 | CONVERTER MOD DC/DC 48V 50W |
| VE-BT4-MY-F2 | CONVERTER MOD DC/DC 48V 50W |
| VE-B5Z-MY-F4 | CONVERTER MOD DC/DC 2V 20W |
| 74ACT139SJ | DECODER/DEMUX 1-OF-4 16SOP |
| ISL22419WFU8Z-TK | IC POT DGTL 128TP LN LP 8-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22329WFU10Z | 功能描述:IC POT DGTL 128TP LN LP 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| ISL22329WFU10Z-TK | 功能描述:IC POT DGTL 128TP LN LP 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| ISL22343 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometer XDCP |
| ISL22343TFR20Z | 功能描述:數字電位計 IC 261 TAP FL RNG IND QD I2C DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22343TFR20Z-TK | 功能描述:數字電位計 IC 264 TAP FL RNG IND QD I2C DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。