- 您現在的位置：買賣IC網 > PDF目錄9256 > ISL23448UFRZ-TK (Intersil)IC DGTL POT 4CH 50K 20QFN PDF資料下載
參數資料
| 型號： | ISL23448UFRZ-TK |
| 廠商： | Intersil |
| 文件頁數： | 7/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DGTL POT 4CH 50K 20QFN |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 電阻（歐姆）： | 50k |
| 電路數： | 4 |
| 溫度系數： | 標準值 65 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 20-QFN（3x4） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁
ISL23448
15
FN7905.0
August 19, 2011
When the device enters shutdown, all current DCP WR settings are
maintained. When the device exits shutdown, the wipers will return
to the previous WR settings after a short settling time (see
Figure 26).
In shutdown mode, if there is a glitch on the power supply which
causes it to drop below 1.3V for more than 0.2 to 0.4s the
wipers will be RESET to their mid position. This is done to avoid
an undefined state at the wiper outputs.
SPI Serial Interface
The ISL23448 supports an SPI serial protocol, mode 0. The
device is accessed via the SDI input and SDO output with data
clocked in on the rising edge of SCK, and clocked out on the
falling edge of SCK. CS must be LOW during communication with
the ISL23448. The SCK and CS lines are controlled by the host or
master. The ISL23448 operates only as a slave device.
All communication over the SPI interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
The SPI protocol contains Instruction Byte followed by one or more
Data Bytes. A valid Instruction Byte contains instruction as the three
MSBs, with the following five register address bits (see Table 3).
The next byte sent to the ISL23448 is the Data Byte.
Table 4 contains a valid instruction set for ISL23448.
If the [R4:R0] bits are zero, one, two or three then the read or write
is to the WRi register. If the [R4:R0] are 10000, then the operation
is to the ACR.
Write Operation
A write operation to the ISL23448 is a two or more bytes
operation. First, it requires that the CS transition from
HIGH-to-LOW. Then, the host sends a valid Instruction Byte,
followed by one or more Data Bytes to the SDI pin. The host
terminates the write operation by pulling the CS pin from
LOW-to-HIGH. Instruction is executed on the rising edge of CS
(see Figure 27).
Read Operation
A Read operation to the ISL23448 is a four byte operation. First,
it requires that the CS transition from HIGH-to-LOW. Then, the
host sends a valid Instruction Byte, followed by a “dummy” Data
Byte, NOP Instruction Byte and another “dummy” Data Byte to
the SDI pin. The SPI host receives the Instruction Byte (instruction
code + register address) and requested Data Byte from the SDO
pin on the rising edge of SCK during the third and fourth bytes,
respectively. The host terminates the read by pulling the CS pin
from LOW-to-HIGH (see Figure 28).
FIGURE 26. SHUTDOWN MODE WIPER RESPONSE
POWER-UP
USER PROGRAMMED
MID SCALE = 40H
SHDN ACTIVATED SHDN RELEASED
AFTER SHDN
WIPE
R
V
O
LT
AGE
,
V
RW
(V
)
SHDN MODE
TIME (s)
WIPER RESTORE TO
THE ORIGINAL POSITION
0
TABLE 3. INSTRUCTION BYTE FORMAT
BIT #
7
654321
0
I2
I1
I0
R4
R3
R2
R1
R0
TABLE 4. INSTRUCTION SET
INSTRUCTION SET
OPERATION
I2
I1
I0
R4
R3
R2
R1
R0
0
XXX
XX
NOP
0
1
XXX
XX
ACR READ
0
1
XXX
XX
ACR WRTE
1
0
R4R3R2R1R0
WRi or ACR READ
1
0
R4R3R2R1R0
WRi or ACR WRTE
Where X means “do not care”.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27466T21F11PA | CONN RCPT 11POS WALL MT W/PINS |
| VE-24J-MX-B1 | CONVERTER MOD DC/DC 36V 75W |
| VI-26F-MY-F2 | CONVERTER MOD DC/DC 72V 50W |
| ISL23448TFVZ-TK | IC DGTL POT 4CH 100K 20TSSOP |
| DS1010-125 | IC DELAY LINE 10TAP 125NS 14-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL23448UFVZ | 功能描述:數字電位計 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23448UFVZ-T7A | 功能描述:數字電位計 IC 128 TAPVOLATILE SPI QUAD RNG IND 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23448UFVZ-TK | 功能描述:數字電位計 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23448WFRZ | 功能描述:數字電位計 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23448WFRZ-T7A | 功能描述:數字電位計 IC 128 TAPVOLATILE SPI QUAD RNG IND 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。