- 您現在的位置：買賣IC網 > PDF目錄9996 > ISL26310FBZ-T7A (Intersil)IC ADC 12BIT SPI/SRL 125K 8SOIC PDF資料下載
參數資料
| 型號： | ISL26310FBZ-T7A |
| 廠商： | Intersil |
| 文件頁數： | 13/23頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SPI/SRL 125K 8SOIC |
| 標準包裝： | 250 |
| 位數： | 12 |
| 采樣率（每秒）： | 125k |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 80mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁
ISL26310, ISL26311, ISL26312, ISL26313, ISL26314, ISL26315, ISL26319
20
FN7549.2
February 26, 2014
Device Configuration Registers
The Input Multiplexer Channel Select and power management
features are controlled by loading the appropriate bits into the
16-bit Configuration Register through the serial port, MSB-first,
as shown below. The first two Load bits LD1-LD0 must be set to
“11” in order to perform a Register update: any other setting will
leave the Register unchanged. Changes to the Configuration
Register will be implemented internally immediately following
the completion of the current conversion, or require a dummy
conversion in order to take effect. Also, in the case of all power
management features, a recovery time will be incurred when
returning to normal operation, as indicated.
Power Management Modes
In all SPI interface modes (RAC, RDC, etc.) the device has three
states of operation: Acquisition, Conversion and Idle. Power
management modes decide the state of the ADC in Idle mode
and are selected by the PM bits in the Configuration Register as
In the default mode (Continuous Operation) the ADC is fully
powered in the Idle state and can be taken back to the
Acquisition state instantaneously. In this mode the ADC can be
operated with maximum throughput and hence is ideally suitable
for applications where the ADC is operated continuously.
In Auto Sleep Mode the ISL263XX will be in a sleep state
consuming less than 0.4mA. However, it should be noted that the
requirements on tACQ are more stringent in Auto Sleep mode
since the device must wake up and then perform the Acquisition.
In Auto Power Down Mode (as selected by PM bits) the ADC will be in
power-down condition during the Idle period, consuming less than
5A of current. Wake-up time takes 150s. The acquisition time
(tACQ) must be increased to account for this delay.
The power management modes provide a high degree of
flexibility in trading average power consumption versus the
required throughput. Significant power savings can be achieved
by operating in either Auto Sleep Mode or Auto Power-Down
mode depending on the throughput requirements.
TABLE 3. CONFIGURATION REGISTER
BIT 15
(MSB)
14
13
12
11
10
9
8
LD1
LD0
ADDR2
ADDR1
ADDR0
PM1
PM0 Unused
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2 BIT 1
BIT 0
(LSB)
RGRD
Unused
TABLE 4. CONFIGURATION REGISTER 2
BIT(S)
DESCRIPTION
15:14 Register Load word, set to “11” to update registers,
otherwise previous settings are retained.
13:11 Multiplexer Channel Select word ADDR2:0.
000H: Channel AIN0 (single-ended input devices) or AIN0+/AIN0-
(differential input devices).
001H: Channel AIN1 or AIN1+/AIN1-
010H: Channel AIN2 or AIN2+/AIN2-
011H: Channel AIN3 or AIN3+/AIN3-
100H: Channel AIN4
101H: Channel AIN5
110H: Channel AIN6
111H: Channel AIN7
10:9 Power Management Configuration Control.
00H: Auto Power-Down mode. Device will go into Power-down
mode automatically at the end of the next conversion cycle.
01H: Continuous Operation mode (default). Device remains fully
powered at all times.
1xH: Auto Sleep Mode. Device will enter reduced-power Sleep
mode automatically at the end of the next conversion cycle. A "1"
in PM1 overrides the setting in PM0.
8Unused.
7
Register readback mode. "1" means register readback is enabled
resulting in configuration settings to be output along with
conversion results. "0" (default) mode of operation register
settings are not output.
6:0 Unused.
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/24FE26SA | CONN RCPT 26POS JAM NUT W/SCKT |
| MS27508E12F8PC | CONN RCPT 8POS BOX MNT W/PINS |
| MS27484T18A32PA | CONN PLUG 32POS STRAIGHT W/PINS |
| MS27466T11B98PA | CONN RCPT 6POS WALL MT W/PINS |
| MS27467T9B35PD | CONN PLUG 6POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL26311 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:12-bit, 125kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels |
| ISL26311FBZ | 制造商:Intersil Corporation 功能描述:ISL26311FBZ 12-BIT, 125KSPS, SINGLE CH/ENDED DIFFERENTIAL SA - Rail/Tube 制造商:Intersil Corporation 功能描述:IC ADC 12BIT SPI/SRL 125K 8-SOIC |
| ISL26311FBZ-T | 制造商:Intersil Corporation 功能描述:ISL26311FBZ 12-BIT, 125KSPS, SINGLE CH/ENDED DIFFERENTIAL SA - Tape and Reel 制造商:Intersil Corporation 功能描述:IC ADC 12BIT SPI/SRL 125K 8-SOIC |
| ISL26311FBZ-T7A | 制造商:Intersil Corporation 功能描述:ISL26311FBZ 12-BIT, 125KSPS, SINGLE CH/ENDED DIFFERENTIAL SA - Tape and Reel 制造商:Intersil Corporation 功能描述:IC ADC 12BIT SPI/SRL 125K 8SOIC |
| ISL26312 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:12-bit, 125kSPS Low-power ADCs with Single-ended and Differential Inputs and Multiple Input Channels |
發布緊急采購，3分鐘左右您將得到回復。