參數資料
型號: ISL28272FAZ
廠商: Intersil
文件頁數: 3/14頁
文件大?。?/td> 0K
描述: IC INSTR AMP RRIO SGL 16-QSOP
標準包裝: 97
放大器類型: 儀表
電路數: 2
輸出類型: 滿擺幅
轉換速率: 0.5 V/µs
-3db帶寬: 100kHz
電流 - 輸入偏壓: 10pA
電壓 - 輸入偏移: 35µV
電流 - 電源: 120µA
電流 - 輸出 / 通道: 31mA
電壓 - 電源,單路/雙路(±): 2.4 V ~ 5.5 V,±1.2 V ~ 2.75 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 16-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 16-QSOP
包裝: 管件
11
FN6390.2
August 17, 2007
Application Information
Product Description
The ISL28271 and ISL28272 are dual channel micropower
instrumentation amplifiers (in-amps) which deliver rail-to-rail
input amplification and rail-to-rail output swing. The in-amps
also deliver excellent DC and AC specifications while
consuming only about 120A for both channels. Because
the independent pair of feedback terminals set the gain and
adjust the output zero level, the ISL28271 and ISL28272
achieve high CMRR regardless of the tolerance of the gain
setting resistors. The ISL28271 is internally compensated for
a minimum gain of 10. The ISL28272 is internally
compensated for a minimum gain of 100.
EN pins are available to independently enable or disable a
channel. When all channels are off, current consumption is
down to typically 4A.
Input Protection
All input terminals and feedback terminals have internal ESD
protection diodes to both positive and negative supply rails,
limiting the input voltage to within one diode beyond the
supply rails. Input signals originating from low impedance
sources should have current limiting resistors in series with
the IN+ and IN- pins to prevent damaging currents during
power supply sequencing and other transient conditions.
The ISL28272 has additional back-to-back diodes across the
input terminals and also across the feedback terminals. If
overdriving the inputs is necessary, the external input current
must never exceed 5mA. External series resistors may be
used as an external protection to limit excessive external
voltage and current from damaging the inputs. On the other
hand, the ISL28271 has no clamps to limit the differential
voltage on the input terminals allowing higher differential
input voltages at lower gain applications. It is recommended
however, that the terminals of the ISL28271 are not
overdriven beyond 1V to avoid offset drift.
Input Stage and Input Voltage Range
The input terminals (IN+ and IN-) of the in-amps are a single
differential pair of CMOS devices aided by an Input Range
Enhancement Circuit, IREC, to increase the headroom of
operation of the common-mode input voltage. The feedback
terminals (FB+ and FB-) also have a similar topology. As a
result, the input common-mode voltage range is rail-to-rail
regardless of the feedback terminal settings and regardless
of the gain settings. They are able to handle input voltages
that are at or slightly beyond the supply and ground sensing
making these in-amps well suited for single 5V down to 2.4V
supply systems.
The IREC enables rail-to-rail input amplification without the
problems usually associated with the dual differential stage
topology. The IREC ensures that there are no drastic
changes in offset voltage over the entire range of the input.
See Input Offset Voltage vs Common-Mode Input Voltage in
performance charts. IREC also cures the abrupt change and
even reverse polarity of the input bias current over the whole
range of input.
Output Stage and Output Voltage Range
A Class AB common-source output stage drives the output.
The pair of complementary MOSFET devices drive the
output VOUT to within a few millivolts of the supply rails. At a
100k
Ω load, the PMOS sources current and pulls the output
up to 4mV below the positive supply. The NMOS sinks
current and pulls the output down to 4mV above the negative
supply, or ground in the case of a single supply operation.
The current sinking and sourcing capability are internally
limited to 31mA. When disabled, the outputs are in a high
impedance state.
Gain Setting
VIN, the potential difference across IN+ and IN-, is replicated
(less the input offset voltage) across FB+ and FB-. The
function of the in-amp is to maintain the differential voltage
across FB- and FB+ equal to IN+ and IN-; (FB- - FB+) =
(IN+ - IN-). Consequently, the transfer function can be
derived. The in-amp gain is set by two external resistors, the
feedback resistor RF, and the gain resistor RG.
In Figure 37, the FB+ pin and one end of resistor RG are
connected to GND. With this configuration, Equation 1 is
only true for a positive swing in VIN; negative input swings
will be ignored because the output will be at ground.
Reference Connection
Unlike a three op amp in-amp realization, a finite series
resistance seen at the REF terminal does not degrade the
high CMRR performance eliminating the need for an
additional external buffer amplifier. Figure 38 uses the FB+
pin to provide a high impedance REF terminal.
+
-
+
-
IN+
IN-
FB+
FB-
V+
V-
EN
2.4V TO 5.5V
RF
RG
VOUT
EN
ISL28271
VCM
IN+
IN-
FIGURE 37. GAIN IS SET BY TWO EXTERNAL RESISTORS,
RF AND RG
ISL28272
VOUT
1
R
F
R
G
--------
+
VIN
=
VIN
IN+
IN-
=
(EQ. 1)
ISL28271, ISL28272
相關PDF資料
PDF描述
HMTSW-120-07-G-T CONN HEADER 60POS .25 GLD
MCS1632R005FER RES CURRENT SENSE .005 OHM 1W 1%
HMTSW-120-07-G-T-240 CONN HEADER 60POS .100" T/H GOLD
TMMH-125-01-F-D-RA-ES CONN HEADR 50POS DBL 2MM T/H
155234-5203-RA CONN HDR 2MM 34POS 10U" AU RA
相關代理商/技術參數
參數描述
ISL28272FAZ-T7 功能描述:IC INSTR AMP RRIO DUAL 16-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SO 包裝:管件
ISL28272INEVAL1Z 功能描述:EVALUATION BOARD FOR ISL28272 RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
ISL28273 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual and Quad Channel Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifiers
ISL28273FAZ 功能描述:IC OPAMP DUAL RRIO MCPWR 16-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:75 系列:MicroAmplifier™ 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.03 V/µs 增益帶寬積:100kHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:60µV 電流 - 電源:20µA 電流 - 輸出 / 通道:5mA 電壓 - 電源,單路/雙路(±):2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SOIC 包裝:管件
ISL28273FAZ-T7 功能描述:IC OPAMP DUAL RRIO MCPWR 16-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SO 包裝:管件