參數資料
型號: ISL28474EVAL1Z
廠商: Intersil
文件頁數: 8/18頁
文件大小: 0K
描述: EVALUATION BOARD FOR ISL28474
標準包裝: 1
每 IC 通道數: 4 - 四
放大器類型: 儀表
輸出類型: 單端,滿擺幅
轉換速率: 0.5 V/µs
電流 - 輸出 / 通道: 31mA
工作溫度: -40°C ~ 125°C
電流供應(主 IC): 240µA
電壓 - 電源,單路/雙路(±): 2.4 V ~ 5 V,±1.2 V ~ 2.5 V
板類型: 完全填充
已供物品:
已用 IC / 零件: ISL28474
16
FN6345.3
May 14, 2009
Input Stage and Input Voltage Range
The input terminals (IN+ and IN-) of both amplifiers “A” and
“B” are single differential pair P-MOSFET devices aided by
an Input Range Enhancement Circuit to increase the
headroom of operation of the common-mode input voltage.
The feedback terminals (FB+ and FB-) of amplifier “A” also
have a similar topology. As a result, the input common-mode
voltage range is rail-to-rail. These amps are able to handle
input voltages that are at or slightly beyond the supply and
ground making them well suited for single 5V or 3.3V low
voltage supply systems. There is no need then to move the
common-mode input to achieve symmetrical input voltage.
Output Stage and Output Voltage Range
A pair of complementary MOSFET devices drives the output
VOUT to within a few mV of the supply rails. At a 100kΩ load,
the PMOS sources current and pulls the output up to 4mV
below the positive supply, while the NMOS sinks current and
pulls the output down to 3mV above the negative supply, or
ground in the case of a single supply operation. The current
sinking and sourcing capability of the ISL28274 are internally
limited to 31mA.
Gain Setting of Instrumentation Amp “A”
VIN, the potential difference across IN+ and IN-, is replicated
(less the input offset voltage) across FB+ and FB-. The goal
of the ISL28274 in-amp is to maintain the differential voltage
across FB+ and FB- equal to IN+ and IN-;
(FB+ - FB-) = (IN+ - IN-). Consequently, the transfer function
can be derived. The gain is set by two external resistors, the
feedback resistor RF, and the gain resistor RG.
In Figure 61, the FB+ pin and one end of resistor RG are
connected to GND. With this configuration, Equation 1 is
only true for a positive swing in VIN; negative input swings
will be ignored and the output will be at ground.
Reference Connection
Unlike a three-op amp instrumentation amplifier, a finite
series resistance seen at the REF terminal does not degrade
the high CMRR performance, eliminating the need for an
additional external buffer amplifier. Figure 62 uses the FB+
pin to provide a high impedance REF terminal.
The FB+ pin is used as a REF terminal to center or to adjust
the output. Because the FB+ pin is a high impedance input,
an economical resistor divider can be used to set the voltage
at the REF terminal without degrading or affecting the CMRR
performance. Any voltage applied to the REF terminal will
shift VOUT by VREF times the closed loop gain, which is set
by resistors RF and RG as shown in Figure 62.
The FB+ pin can also be connected to the other end of resistor,
RG. See Figure 63. Keeping the basic concept that the in-amps
maintain constant differential voltage across the input terminals
and feedback terminals (IN+ - IN- = FB+ - FB-), the transfer
function of Figure 63 can be derived.
7
6
5
3
4
8
16
2
+
-
+
-
IN+
IN-
FB+
FB-
V+
V-
2.4V TO 5V
RF
RG
VOUT
ISL28274
VCM
VIN/2
FIGURE 61. GAIN IS BY EXTERNAL RESISTORS RF AND RG
AMP “A”
VOUT
1
R
F
R
G
--------
+
VIN
=
(EQ. 1)
FIGURE 62. GAIN SETTING AND REFERENCE CONNECTION
7
6
5
3
4
8
16
2
+
-
+
-
IN+
IN-
FB+
FB-
V+
V-
2.4V TO 5V
RF
RG
VOUT
ISL28274
VCM
VIN/2
R1
R2
REF
2.4V to 5V
AMP “A”
VOUT
1
R
F
R
G
--------
+
VIN
()
1
R
F
R
G
--------
+
VREF
()
+
=
(EQ. 2)
7
6
5
3
4
8
16
2
+
-
+
-
IN+
IN-
FB+
FB-
V+
V-
2.4V TO 5V
RF
RG
VOUT
ISL28274
VCM
VIN/2
VREF
FIGURE 63. REFERENCE CONNECTION WITH AN AVAILABLE
VREF
AMP “A”
ISL28274, ISL28474
相關PDF資料
PDF描述
GEM25DTMI-S189 CONN EDGECARD 50POS R/A .156 SLD
LM4050AEX3-2.1+T IC VREF SHUNT PREC 2.048V SC70-3
VI-2N3-EY CONVERTER MOD DC/DC 24V 50W
GCM15DTMS-S189 CONN EDGECARD 30POS R/A .156 SLD
16PX100MEFCTA5X11 CAP ALUM 100UF 16V 20% RADIAL
相關代理商/技術參數
參數描述
ISL28474FAZ 功能描述:IC OPAMP QUAD RRIO MCPWR 24-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 5.5 V,±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR
ISL28474FAZ-T7 功能描述:IC OPAMP QUAD RRIO MCPWR 24-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 5.5 V,±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR
ISL28476 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual and Quad Precision Micropower Single Supply Rail-to-Rail Input and Output Precision Op Amps
ISL28476EVAL1Z 功能描述:EVALUATION BOARD FOR ISL28476 RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
ISL28476FAZ 功能描述:IC OPAMP QUAD RRIO MCPWR 16-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 5.5 V,±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR