- 您現在的位置：買賣IC網 > PDF目錄16886 > ISL28474EVAL1Z (Intersil)EVALUATION BOARD FOR ISL28474 PDF資料下載
參數資料
| 型號： | ISL28474EVAL1Z |
| 廠商： | Intersil |
| 文件頁數： | 9/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION BOARD FOR ISL28474 |
| 標準包裝： | 1 |
| 每 IC 通道數： | 4 - 四 |
| 放大器類型： | 儀表 |
| 輸出類型： | 單端，滿擺幅 |
| 轉換速率： | 0.5 V/µs |
| 電流 - 輸出 / 通道： | 31mA |
| 工作溫度： | -40°C ~ 125°C |
| 電流供應（主 IC）： | 240µA |
| 電壓 - 電源，單路/雙路(±)： | 2.4 V ~ 5 V，±1.2 V ~ 2.5 V |
| 板類型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL28474 |
17
FN6345.3
May 14, 2009
A finite resistance RS in series with the VREF source, adds an
output offset of VIN*(RS/RG). As the series resistance RS
approaches zero, the gain equation is simplified to Equation 3
for Figure 63. VOUT is simply shifted by an amount VREF.
External Resistor Mismatches
Because of the independent pair of feedback terminals
provided by the ISL28274, the CMRR is not degraded by
any resistor mismatches. Hence, unlike a three op amp and
especially a two op amp in-amp, the ISL28274 reduces the
cost of external components by allowing the use of 1% or
more tolerance resistors without sacrificing CMRR
performance. The ISL28274 CMRR will be 100dB
regardless of the tolerance of the resistors used.
Using Only the Instrumentation Amplifier
If the application only requires the instrumentation amp, the
user must configure the unused op amp to prevent it from
oscillating. The unused op amp will oscillate if the input and
output pins are floating. This will result in higher than
expected supply currents and possible noise injection into
the in-amp. The proper way to prevent this oscillation is to
short the output to the negative input and ground the positive
input (as shown in Figure 64).
Proper Layout Maximizes Performance
To achieve the maximum performance of the high input
impedance and low offset voltage, care should be taken in
the circuit board layout. The PC board surface must remain
clean and free of moisture to avoid leakage currents
between adjacent traces. Surface coating of the circuit board
will reduce surface moisture and provide a humidity barrier,
reducing parasitic resistance on the board. When input
leakage current is a concern, the use of guard rings around
the amplifier inputs will further reduce leakage currents.
Figure 65 shows a guard ring example for a unity gain
amplifier that uses the low impedance amplifier output at the
same voltage as the high impedance input to eliminate
surface leakage. The guard ring does not need to be a
specific width, but it should form a continuous loop around
both inputs. For further reduction of leakage currents,
components can be mounted to the PC board using Teflon
standoff insulators.
Current Limiting
The ISL28274 has no internal current-limiting circuitry. If the
output is shorted, it is possible to exceed the Absolute
Maximum Rating for output current or power dissipation,
potentially resulting in the destruction of the device.
Power Dissipation
It is possible to exceed the +150°C maximum junction
temperatures under certain load and power-supply
conditions. It is therefore important to calculate the
maximum junction temperature (TJMAX) for all applications
to determine if power supply voltages, load conditions, or
package type need to be modified to remain in the safe
operating area. These parameters are related in Equation 4:
where:
PDMAXTOTAL is the sum of the maximum power
dissipation of each amplifier in the package (PDMAX)
PDMAX for each amplifier can be calculated as shown in
Equation 5:
where:
TMAX = Maximum ambient temperature
θ
JA = Thermal resistance of the package
PDMAX = Maximum power dissipation of 1 amplifier
VS = Supply voltage (Magnitude of V+ and V-)
IMAX = Maximum supply current of 1 amplifier
VOUTMAX = Maximum output voltage swing of the
application
RL = Load resistance
VOUT
1
R
F
R
G
--------
+
VIN
()
VREF
()
+
=
(EQ. 3)
FIGURE 64. PREVENTING OSCILLATIONS IN UNUSED
CHANNELS
-
+
1/2 ISL28274
IN
V+
FIGURE 65. GUARD RING EXAMPLE FOR UNITY GAIN
AMPLIFIER
HIGH IMPEDANCE INPUT
1/4 ISL28474
T
JMAX
T
MAX
θ
JAxPDMAXTOTAL
()
+
=
(EQ. 4)
PD
MAX
2*V
S
I
SMAX
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
(EQ. 5)
ISL28274, ISL28474
相關PDF資料 |
PDF描述 |
|---|---|
| GEM25DTMI-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| LM4050AEX3-2.1+T | IC VREF SHUNT PREC 2.048V SC70-3 |
| VI-2N3-EY | CONVERTER MOD DC/DC 24V 50W |
| GCM15DTMS-S189 | CONN EDGECARD 30POS R/A .156 SLD |
| 16PX100MEFCTA5X11 | CAP ALUM 100UF 16V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL28474FAZ | 功能描述:IC OPAMP QUAD RRIO MCPWR 24-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| ISL28474FAZ-T7 | 功能描述:IC OPAMP QUAD RRIO MCPWR 24-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| ISL28476 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual and Quad Precision Micropower Single Supply Rail-to-Rail Input and Output Precision Op Amps |
| ISL28476EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL28476 RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| ISL28476FAZ | 功能描述:IC OPAMP QUAD RRIO MCPWR 16-QSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
發布緊急采購，3分鐘左右您將得到回復。