- 您現在的位置：買賣IC網 > PDF目錄16324 > ISL41334EVAL1Z (Intersil)EVALUATION BOARD FOR ISL41334 PDF資料下載
參數資料
| 型號： | ISL41334EVAL1Z |
| 廠商： | Intersil |
| 文件頁數： | 8/28頁 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR ISL41334 |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1 |
| 主要目的： | 接口，收發器，RS-232，RS-422，RS-485 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ISL41334 |
| 主要屬性： | 2 個驅動器，2 個接收器 - RS-232 模式 |
| 次要屬性： | 1 個驅動器，1 個接收器 - RS-422/RS-485 模式 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
16
FN6202.3
November 21, 2007
SSOP) receiver outputs are not independently tri-statable.
ISL41334 (QFN) receiver outputs are tri-statable via an
active low RXEN input for each port (see “ISL41334 (QFN
Package) Special Features” on page 17 for more details).
TX FEATURES
The RS-485, RS-422 driver is a differential output device
that delivers at least 2.2V across a 54
Ω load (RS-485), and
at least 2.5V across a 100
Ω load (RS-422). Both levels
significantly exceed the standards requirements, and these
exceptional output voltages increase system noise immunity,
and/or allow for transmission over longer distances. The
drivers feature low propagation delay skew to maximize bit
widths, and to minimize EMI.
To allow multiple drivers on a bus, the RS-485 spec requires
that drivers survive worst case bus contentions undamaged.
The ISL81334, ISL41334 drivers meet this requirement via
driver output short circuit current limits, and on-chip thermal
shutdown circuitry. The output stages incorporate current
limiting circuitry that ensures that the output current never
exceeds the RS-485 specification, even at the common
mode voltage range extremes. In the event of a major short
circuit condition, devices also include a thermal shutdown
feature that disables the drivers whenever the die temperature
becomes excessive. This eliminates the power dissipation,
allowing the die to cool. The drivers automatically re-enable
after the die temperature drops about 15°. If the contention
persists, the thermal shutdown/re-enable cycle repeats until
the fault is cleared. Receivers stay operational during thermal
shutdown.
RS-485 multi-driver operation also requires drivers to include
tri-state functionality, so each port has a DE pin to control
this function. If the driver is used in an RS-422 network, such
that driver tri-state isn’t required, then the DE pin can be left
unconnected and an internal pull-up keeps it in the enabled
state. Drivers are also tri-stated when the IC is in SHDN, or
when the 5V power supply is off.
SPEED OPTIONS
The ISL81334 (SOIC, SSOP) has fixed, high slew rate driver
outputs optimized for 20Mbps data rates. The ISL41334
(QFN) offers three user selectable data rate options: “Fast”
for high slew rate and 20Mbps; “Medium” with slew rate
limiting set for 460kbps; “Slow” with even more slew rate
limiting for 115kbps operation. See “Data Rate, Cables, and
Data Rates” on page 19 for more information.
Receiver performance is the same for all three speed
options.
DATA RATE, CABLES, AND TERMINATIONS
RS-485, RS-422 are intended for network lengths up to
4000’ (1220m), but the maximum system data rate
decreases as the transmission length increases. Devices
operating at the maximum data rate of 20Mbps are limited to
lengths of 20’ to 30’ (6m to 9m), while devices operating at or
below 115kbps can operate at the maximum length of 4000’
(1220m).
Higher data rates require faster edges, so both the
ISL81334, ISL41334 versions offer an edge rate capable of
20Mbps data rates. The ISL41334 also offers two slew rate
limited edge rates to minimize problems at slower data rates.
Nevertheless, for the best jitter performance when driving
long cables, the faster speed settings may be preferable,
even at low data rates. See “RS-485 Slew Rate Limited Data
Rates” on page 19 for details.
Twisted pair is the cable of choice for RS-485, RS-422
networks. Twisted pair cables tend to pick up noise and
other electromagnetically induced voltages as common
mode signals, which are effectively rejected by the
differential receivers in these ICs.
The preferred cable connection technique is “daisy-chaining”,
where the cable runs from the connector of one device directly
to the connector of the next device, such that cable stub
lengths are negligible. A “backbone” structure, where stubs
run from the main backbone cable to each device’s connector,
is the next best choice, but care must be taken to ensure that
each stub is electrically “short”. See Table 4 for recommended
maximum stub lengths for each speed option.
Proper termination is imperative to minimize reflections when
using the 20Mbps speed option. Short networks using the
medium and slow speed options need not be terminated, but
terminations are recommended unless power dissipation is an
overriding concern. Note that the RS-485 specification allows
a maximum of two terminations on a network, otherwise the
Tx output voltage may not meet the required VOD.
In point-to-point, or point-to-multipoint (RS-422) networks,
the main cable should be terminated in its characteristic
impedance (typically 120
Ω) at the end farthest from the
driver. In multi-receiver applications, stubs connecting
receivers to the main cable should be kept as short as
possible, but definitely shorter than the limits shown in
Table 4. Multipoint (RS-485) systems require that the main
cable be terminated in its characteristic impedance at both
ends. Again, keep stubs connecting a transceiver to the
main cable as short as possible, and refer to Table 4. Avoid
“star”, and other configurations, where there are many
“ends” which would require more than the two allowed
terminations to prevent reflections.
TABLE 4. RECOMMENDED STUB LENGTHS
SPEED OPTION
MAXIMUM STUB LENGTH
ft (m)
SLOW
350 to 500 (107 to 152)
MED
100 to 150 (30.5 to 46)
FAST
1 to 3 (0.3 to 0.9)
ISL81334, ISL41334
相關PDF資料 |
PDF描述 |
|---|---|
| H3KKH-3018G | IDC CABLE - HPK30H/AE30G/HPK30H |
| H3WWH-3036G | IDC CABLE - HPL30H/AE30G/HPL30H |
| H3KKH-3036G | IDC CABLE - HPK30H/AE30G/HPK30H |
| GCB13DHRT | CONN CARD EXTEND 26POS .050" SLD |
| VI-J1X-EZ-F2 | CONVERTER MINIMOD DC/DC 5.2V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL41334IRZ | 功能描述:RS-422/RS-485 接口 IC W/ANNEAL DL 5V MULTIPROTOCOL TRANSC RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| ISL41334IRZ-T | 功能描述:TRANSISTOR ESD SGL/DUAL 40-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 產品目錄頁面:1402 (CN2011-ZH PDF) |
| ISL41334IRZ-T7A | 功能描述:IC TXRX RS232/485 DL 2PRT 40QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL41387 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:【15kV ESD Protected, 5V, Dual Protocol (RS-232/RS-485) Transceivers |
| ISL41387EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL41387 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。