- 您現在的位置：買賣IC網 > PDF目錄9865 > ISL41387IRZ-T (Intersil)IC TXRX DUAL PROTOCAL ESD 40-QFN PDF資料下載
參數資料
| 型號： | ISL41387IRZ-T |
| 廠商： | Intersil |
| 文件頁數： | 7/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX DUAL PROTOCAL ESD 40-QFN |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 2/2 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN 裸露焊盤（6x6） |
| 包裝： | 標準包裝 |
| 其它名稱： | ISL41387IRZ-TDKR |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
15
FN6201.3
November 21, 2007
Worst case receiver input currents are 20% lower than the 1
“unit load” (1mA) RS-485 limit, which translates to a 15k
Ω
minimum input resistance.
These receivers include a “full fail-safe” function that
guarantees a high level receiver output if the receiver inputs
are unconnected (floating), shorted together, or if the bus is
terminated but undriven (i.e., differential voltage collapses to
near zero due to termination). Failsafe with shorted, or
terminated and undriven inputs is accomplished by setting
the Rx upper switching point at -40mV, thereby ensuring that
the Rx recognizes a 0V differential as a high level.
All the Rx outputs are short circuit protected, and are
tri-statable via the active high RXEN pin, or when the IC is
(SHDN) Mode” on page 16). ISL41387 (QFN) receiver
outputs are also tri-statable via an active low RXEN input
page 17 for more details).
For the ISL41387 (QFN), when using the active high RXEN
function, the RXEN pin may be left floating (internally pulled
high), or should be connected to VCC through a 1kΩ resistor.
If using the active low RXEN, then the RXEN pin must be
connected to GND.
TX FEATURES
The RS-485, RS-422 driver is a differential output device
that delivers at least 2.2V across a 54
Ω load (RS-485), and
at least 2.5V across a 100
Ω load (RS-422). Both levels
significantly exceed the standards requirements, and these
exceptional output voltages increase system noise immunity,
and/or allow for transmission over longer distances. The
drivers feature low propagation delay skew to maximize bit
widths, and to minimize EMI.
To allow multiple drivers on a bus, the RS-485 specification
requires that drivers survive worst case bus contentions
undamaged. The ISL81387, ISL41387 drivers meet this
requirement via driver output short circuit current limits, and
on-chip thermal shutdown circuitry. The output stages
incorporate current limiting circuitry that ensures that the
output current never exceeds the RS-485 specification, even
at the common mode voltage range extremes. In the event of
a major short circuit condition, devices also include a thermal
shutdown feature that disables the drivers whenever the die
temperature becomes excessive. This eliminates the power
dissipation, allowing the die to cool. The drivers automatically
re-enable after the die temperature drops about 15°. If the
contention persists, the thermal shutdown/re-enable cycle
repeats until the fault is cleared. Receivers stay operational
during thermal shutdown.
RS-485 multi-driver operation also requires drivers to include
tri-state functionality, so the port has a DEN pin to control this
function. If the driver is used in an RS-422 network, such that
driver tri-state isn’t required, then the DEN pin should connect
to VCC through a 1kΩ resistor. Drivers are also tri-stated when
the IC is in SHDN, or when the 5V power supply is off.
SPEED OPTIONS
The ISL81387 (SOIC/SSOP) features two speed options
that are user selectable via the SLEW pin: a high slew rate
setting optimized for 20Mbps data rates (Fast), and a slew
rate limited option for operation up to 460kbps (Med). The
ISL41387 (QFN) offers an additional, more slew rate limited,
option for data rates up to 115kbps (Slow). See “Data Rate,
Rate Limited Data Rates” on page 17 for more information.
Receiver performance is the same for all three speed
options.
DATA RATE, CABLES AND TERMINATIONS
RS-485, RS-422 are intended for network lengths up to
4000’ (1220m), but the maximum system data rate
decreases as the transmission length increases. Devices
operating at the maximum data rate of 20Mbps are limited to
lengths of 20’ to 30’ (6m to 9m), while devices operating at or
below 115kbps can operate at the maximum length of 4000’
(1220m).
Higher data rates require faster edges, so both the
ISL81387, ISL41387 versions offer an edge rate capable of
20Mbps data rates. They both have a second option for
460kbps, but the ISL41387 also offers another, very slew
rate limited, edge rate to minimize problems at slow data
rates. Nevertheless, for the best jitter performance when
driving long cables, the faster speed settings may be
preferable, even at low data rates. See “RS-485 Slew Rate
Limited Data Rates” on page 17 for details.
Twisted pair is the cable of choice for RS-485, RS-422
networks. Twisted pair cables tend to pick up noise and
other electromagnetically induced voltages as common
mode signals, which are effectively rejected by the
differential receivers in these ICs.
The preferred cable connection technique is “daisy-chaining”,
where the cable runs from the connector of one device directly
to the connector of the next device, such that cable stub
lengths are negligible. A “backbone” structure, where stubs
run from the main backbone cable to each device’s connector,
is the next best choice, but care must be taken to ensure that
each stub is electrically “short”. See Table 4 for recommended
maximum stub lengths for each speed option.
TABLE 4. RECOMMENDED STUB LENGTHS
SPEED OPTION
MAXIMUM STUB LENGTH
ft (m)
SLOW
350 to 500 (107 to 152)
MED
100 to 150 (30.5 to 46)
FAST
1 to 3 (0.3 to 0.9)
ISL81387, ISL41387
相關PDF資料 |
PDF描述 |
|---|---|
| MAX158ACAI+T | IC ADC 8BIT 8CH W/MUX&REF 28SSOP |
| MS27473T14A18SB | CONN PLUG 18POS STRAIGHT W/SCKT |
| V24B3V3M100BG | CONVERTER MOD DC/DC 3.3V 100W |
| V24B3V3M100BF3 | CONVERTER MOD DC/DC 3.3V 100W |
| V24B3V3M100BF2 | CONVERTER MOD DC/DC 3.3V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL4221 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kBps, RS-232 Transmitters/Receivers |
| ISL4221E | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:QFN Packaged, 【15kV ESD Protected, +2.7V to +5.5V, 150nA, 250kbps, RS-232 Transmitters/Receivers |
| ISL4221E_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:QFN Packaged, 【15kV ESD Protected, +2.7V to +5.5V, 150nA, 250kBps, RS-232 Transmitters/Receivers |
| ISL4221EIR | 功能描述:IC TXRX RS232 2.7-5.5V ESD 16QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL4221EIR-T | 功能描述:IC TXRX 1TX/1RX 3V RS-232 16-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。