capability from a bipolar ±
參數資料
型號: ISL43240IR-T
廠商: Intersil
文件頁數: 13/14頁
文件大?。?/td> 0K
描述: IC SWITCH QUAD SPDT 20QFN
標準包裝: 6,000
功能: 開關
電路: 4 x SPDT
導通狀態電阻: 20 歐姆
電壓電源: 單/雙電源
電壓 - 電源,單路/雙路(±): 2 V ~ 12 V,±2 V ~ 6 V
電流 - 電源: 10nA
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-VFQFN 裸露焊盤
供應商設備封裝: 20-QFN 裸露焊盤(4x4)
包裝: 帶卷 (TR)
8
Detailed Description
The ISL43240 quad analog switches offer precise switching
capability from a bipolar ±2V to ±6V or a single 2V to 12V
supply with low on-resistance (18
) and high speed
operation (tON =52ns, tOFF = 40ns). The devices are
especially well suited for portable battery powered
equipment thanks to the low operating supply voltage (2V),
low power consumption (5
W), low leakage currents (5nA
max). High frequency applications also benefit from the wide
bandwidth, and the very high off isolation and crosstalk
rejection.
Supply Sequencing And Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to V- (see
Figure 8). To prevent forward biasing these diodes, V+ and
V- must be applied before any input signals, and input signal
voltages must remain between V+ and V-. If these conditions
cannot be guaranteed, then one of the following two
protection methods should be employed.
Logic inputs can easily be protected by adding a 1k
resistor in series with the input (see Figure 8). The resistor
limits the input current below the threshold that produces
permanent damage, and the sub-microamp input current
produces an insignificant voltage drop during normal
operation.
Adding a series resistor to the switch input defeats the purpose
of using a low RON switch, so two small signal diodes can be
added in series with the supply pins to provide overvoltage
protection for all pins (see Figure 8). These additional diodes
limit the analog signal from 1V below V+ to 1V above V-.
Repeat test for all switches.
FIGURE 4. OFF ISOLATION TEST CIRCUIT
Repeat test for all switches.
FIGURE 5. RON TEST CIRCUIT
FIGURE 6. CROSSTALK TEST CIRCUIT
FIGURE 7. CAPACITANCE TEST CIRCUIT
Test Circuits and Waveforms (Continued)
ANALYZER
RL
SIGNAL
GENERATOR
V+
C
0V or 2.4V
NO or NC
COM
IN
GND
C
V-
V+
C
0.8V or 2.4V
NO or NC
COM
IN
GND
VNX
V1
RON = V1/1mA
1mA
C
V-
0V or 2.4V
ANALYZER
V+
C
NO1 or NC1
SIGNAL
GENERATOR
RL
GND
IN1
COM1
IN2
50
0V or 2.4V
NO
COM2
NO2 or NC2
C
V-
CONNECTION
V+
GND
NO or NC
COM
IN
IMPEDANCE
ANALYZER
0V or 2.4V
V-
ISL43240
相關PDF資料
PDF描述
ISL43410IU-T IC SWITCH DPDT 10MSOP
ISL43640IU-T IC MUX/DEMUX 4X1 10MSOP
ISL43741IR-T IC MUX/DEMUX DUAL 4X1 20QFN
ISL43840IR-T IC MUX/DEMUX DUAL 4X1 20QFN
ISL43841IR-T IC MUX/DEMUX DUAL 4X1 20QFN
相關代理商/技術參數
參數描述
ISL43240IRZ 功能描述:模擬開關 IC SWITCH 4X SPDT +/-5V 18OHM 20QFN(4X4 IND RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
ISL43240IRZ-T 功能描述:模擬開關 IC SWITCH 4X SPDT +/-5V 18OHM 20QFN(4X4 IND RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
ISL43410 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, DPDT High Performance Analog Switch
ISL43410_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, DPDT High Performance Analog Switch
ISL43410IR 功能描述:模擬開關 IC SINGLE DPDT NO RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16