- 您現在的位置：買賣IC網 > PDF目錄1927 > ISL43240IR-T (Intersil)IC SWITCH QUAD SPDT 20QFN PDF資料下載
參數資料
| 型號： | ISL43240IR-T |
| 廠商： | Intersil |
| 文件頁數： | 14/14頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH QUAD SPDT 20QFN |
| 標準包裝： | 6,000 |
| 功能： | 開關 |
| 電路： | 4 x SPDT |
| 導通狀態電阻： | 20 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 2 V ~ 12 V，±2 V ~ 6 V |
| 電流 - 電源： | 10nA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 20-QFN 裸露焊盤（4x4） |
| 包裝： | 帶卷 (TR) |
9
The low leakage current performance is unaffected by this
approach, but the switch resistance may increase, especially
at low supply voltages.
Power-Supply Considerations
The ISL43240 construction is typical of most CMOS analog
switches, in that they have three supply pins: V+, V-, and
GND. V+ and V- drive the internal CMOS switches and set
their analog voltage limits, so there are no connections
between the analog signal path and GND. Unlike switches
with a 13V maximum supply voltage, the ISL43240 15V
maximum supply voltage provides plenty of room for the
10% tolerance of 12V supplies (±6V or 12V single supply),
as well as room for overshoot and noise spikes.
This family of switches performs equally well when operated
with bipolar or single voltage supplies. The minimum
recommended supply voltage is 2V or ±2V. It is important to
note that the input signal range, switching times, and on-
resistance degrade at lower supply voltages. Refer to the
electrical specification tables and Typical Performance
curves for details.
V+ and GND power the internal logic (thus setting the digital
switching point) and level shifters. The level shifters convert
the logic levels to switched V+ and V- signals to drive the
analog switch gate terminals.
Logic-Level Thresholds
V+ and GND power the internal logic stages, so V- has no
affect on logic thresholds. This switch family is TTL
compatible (0.8V and 2.4V) over a V+ supply range of 2.5V
For best results with a 12V supply, use a logic family the
provides a VOH greater than 3V.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails (see
Figure 18). Driving the digital input signals from GND to V+
with a fast transition time minimizes power dissipation. The
ISL43240 has been designed to minimize the supply current
whenever the digital input voltage is not driven to the supply
rails (0V to V+). For example driving the device with 3V logic
(0V to 3V) while operating with dual or single 5V supplies the
device draws only 10
A of current (see Figure 18 for V
IN =
3V). Similiar devices of competitors can draw 8 times this
amount of current.
High-Frequency Performance
In 5
0 systems, signal response is reasonably flat even past
frequency response is very consistent over a wide V+ range,
and for varying analog signal levels.
An off switch acts like a capacitor and passes higher
frequencies with less attenuation, resulting in signal
feedthrough from a switch’s input to its output. Off Isolation
is the resistance to this feedthrough, while Crosstalk
indicates the amount of feedthrough from one switch to
another. Figure 20 details the high Off Isolation and
Crosstalk rejection provided by this switch. At 10MHz, off
isolation is about 50dB in 5
0 systems, decreasing
approximately 20dB per decade as frequency increases.
Higher load impedances decrease Off Isolation and
Crosstalk rejection due to the voltage divider action of the
switch OFF impedance and the load impedance.
Leakage Considerations
Reverse ESD protection diodes are internally connected
between each analog-signal pin and both V+ and V-. One
of these diodes conducts if any analog signal exceeds V+
or V-.
Virtually all the analog leakage current comes from the ESD
diodes to V+ or V-. Although the ESD diodes on a given
signal pin are identical and therefore fairly well balanced,
they are reverse biased differently. Each is biased by either
V+ or V- and the analog signal. This means their leakages
will vary as the signal varies. The difference in the two diode
leakages to the V+ and V- pins constitutes the analog-signal-
path leakage current. All analog leakage current flows
between each pin and one of the supply terminals, not to the
other switch terminal. This is why both sides of a given
switch can show leakage currents of the same or opposite
polarity. There is no connection between the analog signal
paths and GND.
FIGURE 8. OVERVOLTAGE PROTECTION
V-
VCOM
VNO or NC
OPTIONAL PROTECTION
V+
INX
DIODE
OPTIONAL PROTECTION
DIODE
OPTIONAL
PROTECTION
RESISTOR
ISL43240
相關PDF資料 |
PDF描述 |
|---|---|
| ISL43410IU-T | IC SWITCH DPDT 10MSOP |
| ISL43640IU-T | IC MUX/DEMUX 4X1 10MSOP |
| ISL43741IR-T | IC MUX/DEMUX DUAL 4X1 20QFN |
| ISL43840IR-T | IC MUX/DEMUX DUAL 4X1 20QFN |
| ISL43841IR-T | IC MUX/DEMUX DUAL 4X1 20QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL43240IRZ | 功能描述:模擬開關 IC SWITCH 4X SPDT +/-5V 18OHM 20QFN(4X4 IND RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| ISL43240IRZ-T | 功能描述:模擬開關 IC SWITCH 4X SPDT +/-5V 18OHM 20QFN(4X4 IND RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| ISL43410 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, DPDT High Performance Analog Switch |
| ISL43410_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, DPDT High Performance Analog Switch |
| ISL43410IR | 功能描述:模擬開關 IC SINGLE DPDT NO RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。