- 您現在的位置：買賣IC網 > PDF目錄1928 > ISL54405IVZ (Intersil)IC MUX STEREO 2:1 CD/MP3 16TSSOP PDF資料下載
參數資料
| 型號： | ISL54405IVZ |
| 廠商： | Intersil |
| 文件頁數： | 3/19頁 |
| 文件大小： | 0K |
| 描述： | IC MUX STEREO 2:1 CD/MP3 16TSSOP |
| 標準包裝： | 96 |
| 功能： | 開關 |
| 電路： | 2 x SPDT |
| 導通狀態電阻： | 1.9 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 3.6 V |
| 電流 - 電源： | 55µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1247 (CN2011-ZH PDF) |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
11
FN6699.1
June 5, 2008
COM side (L,R) are activated and inoperable on the signal
side (L1, R1, L2, R2) of the switch. When DIR_SEL = Logic
“0” the C/P shunts are activated on the signal side (L1, R1,
L2, R2) and inoperable on the COM side (L, R).
Logic Levels:
AC/DC, DIR_SEL = Logic “0” (Low) when ≤ 0.5V
AC/DC, DIR_SEL = Logic “1” (High) when ≥1.4V or Floating.
The AC/DC and DIR_SEL have internal pull-up resistors to
the internal 3.3V supply rail and can be driven high or
tri-stated (floated by the processor). They should be driven
to ground for a logic “0” (Low). Note: For 5V applications, the
AC/DC and DIR_SEL pins should never be driven to the
external 5V rail. They need to be driven with 1.8V logic or 3V
logic circuit.
AC Coupled or DC Coupled Operation
The Audio CODEC drivers can be directly coupled to the
ISL54405 when the audio signals from the drivers are
ground referenced or do not have a significant DC offset
voltage, < 50mV. Otherwise the signal should be AC coupled
to the ISL54405 part.
CLICK AND POP OPERATION
The ISL54405 has special circuitry to eliminate click and
pops in the speakers during power-up and power-down of
the Audio CODEC Drivers and during removal and insertion
of headphones.
A different click and pop scheme is required depending on
whether the audio CODEC drivers are AC coupled or DC
coupled to the inputs of the ISL54405 part.
AC COUPLED CLICK AND POP OPERATION
Single supply audio drivers have their signal biased at a DC
offset voltage, usually at 1/2 the DC supply voltage of the
driver. As this DC bias voltage comes up or goes down
during power up or down of the driver a transient can be
coupled into the speaker load through the DC blocking
capacitor (see the “Application Block Diagrams” on page 8).
When a driver is OFF and suddenly turned ON the rapidly
changing DC bias voltage at the output of the driver will
cause an equal voltage at the input side of the switch due to
the fact that the voltage across the blocking capacitor cannot
change instantly. If the switch is in Audio mode or there is no
low impedance path to discharge the capacitor voltage at the
input of the switch, before turning on the switch, a transient
discharge will occur in the speaker, generating a Click and
pop noise.
Proper elimination of a click/pop transient at the speaker
load while powering up or down of the audio driver requires
that the ISL54405 have its C/P shunts activated on the
source side of the switch and then placed in Mute mode.
This allows the transient generated by the audio drivers to
be discharged through the Click and Pop shunt circuitry.
Once the driver DC bias has reached VDD/2 and the
transient on the switch side of the DC blocking capacitor has
been discharged to ground through the C/P shunt circuitry,
the switches can be turned ON and connected through to the
speaker loads without generating an undesirable click/pop in
the speakers.
With a typical DC blocking capacitor of 220F and the C/P
shunt circuitry designed to have a resistance of 40
Ω,
allowing a 100ms wait time to discharge the transient before
placing the switch in the Audio mode will prevent the
transient from getting through to the speaker load. See
beginning on page 13.
DC COUPLED CLICK AND POP OPERATION
The ISL54405 can pass ground referenced audio signals
which allows it to be directly connected to audio drivers that
output ground referenced audio signals, eliminating the need
for a DC blocking capacitor.
Audio drivers that swing around ground however do
generate some DC offset, from a few millivolts to tens of
millivolts. When switching between audio channels or muting
the audio signal these small DC offset levels of the drivers
can generate a transient that can cause un-wanted clicks
and pops in the speaker loads.
In a DC coupled application the C/P shunt resistors placed at
the source side of the switch have no effect in eliminating the
transients at the speaker loads when transitioning in and out
of the mute state or switching between channels. In fact
having these C/P shunts active on the source side only
increase un-neccesary power consumption. So, for DC
coupled connection the C/P shunt circuitry should not be
applied at the source (driver) side of the switch.
For DC coupled applications the ISL54405 has a special
soft-start feature that slowly ramps the DC offset voltage
from the audio driver to the speaker load when turning ON a
switch channel. The ramp rate at the load is determined by
the capacitor value connected at the CAP_SS pin.
Lab experimentation has shown that if you can slow the
voltage ramp rate at the speaker to < 10V/s, you can
eliminate click/pop noise in a speaker. A soft-start capacitor
value of 0.1F provides for 4.5V/s ramp rate and is
Performance Curves” beginning on page 13.
See “MUTE to ON” section on page 10 for more detail of
how soft-start works.
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes or diode stacks from the pin to VDD
and to GND (see Figure 8). To prevent forward biasing these
ISL54405
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54406IRTZ | IC SWITCH DUAL SPST 10-TDFN |
| ISL54410IRUZ-T | IC SW USB/AUDIO DUAL SPT 10UTQFN |
| ISL54415IRUZ-T | IC USB SWITCH DUAL SPDT 10UTQFN |
| ISL54500IRUZ-T | IC SWITCH SPDT SGL 6UTDFN |
| ISL54502IHZ-T | IC SWITCH SPDT SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54405IVZ-T | 功能描述:IC MUX STEREO 2:1 CD/MP3 16TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54406 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Stereo Click and Pop Eliminator with Audio Muting |
| ISL54406EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL54406 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL54406IRTZ | 功能描述:IC SWITCH DUAL SPST 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| ISL54406IRTZ-T | 功能描述:IC SWITCH DUAL SPST 10-TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:2,500 系列:- 功能:視頻交叉點開關 電路:1 x 8:6 導通狀態電阻:- 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3.135 V ~ 5.25 V 電流 - 電源:55mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:24-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1214 (CN2011-ZH PDF) 其它名稱:FMS6502MTC24XTR |
發布緊急采購，3分鐘左右您將得到回復。