- 您現在的位置：買賣IC網 > PDF目錄383143 > ISL6225CA-T (INTERSIL CORP) Dual Mobile-Friendly PWM Controller with DDR Memory Option PDF資料下載
參數資料
| 型號： | ISL6225CA-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Dual Mobile-Friendly PWM Controller with DDR Memory Option |
| 中文描述： | DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | PLASTIC, SSOP-28 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 522K |
| 代理商： | ISL6225CA-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
11
FN9049.7
December 28, 2004
The zero frequency, the amplifier high-frequency gain, and
the modulator gain are chosen to satisfy most typical
applications. The crossover frequency will appear at the
point where the modulator attenuation equals the amplifier
high frequency gain. The only task that the system designer
has to complete is to specify the output filter capacitors to
position the load main pole somewhere within one decade
lower than the amplifier zero frequency. With this type of
compensation plenty of phase margin is easily achieved due
to zero-pole pair phase ‘boost’. Conditional stability may
occur only when the main load pole is positioned too much
to the left side on the frequency axis due to excessive output
filter capacitance. In this case, the ESR zero placed within
10kHz...50kHz range gives some additional phase ‘boost’.
Some phase boost can also be achieved by connecting
capacitor C
z
in parallel with the upper resistor R1 of the
divider that sets the output voltage value, as shown in
Figure 4.
Gate Control Logic
The gate control logic translates generated PWM signals
into gate drive signals providing necessary amplification,
level shift, and shoot-trough protection. Also, it bears some
functions that help to optimize the IC performance over a
wide range of the operational conditions. As MOSFET
switching time can very dramatically from type to type and
with the input voltage, the gate control logic provides
adaptive dead time by monitoring real gate waveforms of
both the upper and the lower MOSFETs.
Dual-Step Conversion
The ISL6225 dual channel controller can be used either in
power systems with a single-stage power conversion when
the battery power is converted into the desired output
voltage in one step, or in the systems where some
intermediate voltages are initially established. The choice of
the approach may be dictated by the overall system design
criteria or simply to be a matter of voltages available to the
system designer, like in the case of PCI card applications.
When the power input voltage is a regulated 5V or 3.3V
system bus, the feed-forward ramp may become too
shallow, which creates the possibility of duty-factor jitter
especially in a noisy environment. The noise susceptibility
when operating from low level regulated power sources can
be improved by connecting the VIN pin to ground. The feed-
forward ramp generator will be internally reconnected from
the VIN pin to the V
CC
pin and the ramp slew rate will be
doubled. Application circuits for dual-step power conversion
are presented in Figures 11 through 15.
Protections
The converter output is monitored and protected against
extreme overload, short circuit, Overvoltage, and
Undervoltage conditions.
A sustained overload on the output sets the PGOOD low and
latches-off the whole chip. The controller operation can be
restored by cycling the VCC voltage or an enable (EN) pin.
Overcurrent Protection
Both PWM controllers use the lower MOSFET’s
on-resistance {r
DS(ON)
} to monitor the current for protection
against shorted outputs. The sensed current from the ISEN
pin is compared with a current set by a resistor connected
from the OCSET pin to ground.
Where, I
OC
is a desired overcurrent protection threshold and
R
CS
is the value of the current sense resistor connected to
the I
SEN
pin.
If the lower MOSFET current exceeds the overcurrent
threshold, a pulse skipping circuit is activated. The upper
MOSFET will not be turned on as long as the sensed
current is higher then the threshold value. This limits the
current supplied by the DC voltage source. This condition
keeps on for eight clock cycles after the overcurrent
comparator was tripped for the first time. If after these first
eight clock cycles the current exceeds the overcurrent
threshold again in a time interval of another eight clock
cycles, the overcurrent protection latches and disables the
chip. If the overcurrent condition goes away during the first
eight clock cycles, normal operation is restored and the
overcurrent circuit resets itself sixteen clock cycles after the
overcurrent threshold was exceeded the first time, Figure 8.
ROCSET
9.6V
---------------------------------------------------------
100
+
(
)
DS ON
)
=
FIGURE 8. OVERCURRENT PROTECTION WAVEFORMS
3
1
2
SHUTDOWN
IL
VOUT
CH3 1.0A
PGOOD
M 10.0μs
CH2 100mV
CH1 5.0V
8 CLK
ISL6225
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6225CAZA | Dual Mobile-Friendly PWM Controller with DDR Memory Option |
| ISL6226 | Advanced PWM and Linear Power Controller for Portable Applications |
| ISL6226EVAL1 | Advanced PWM and Linear Power Controller for Portable Applications |
| ISL6226CA | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6232 | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6225CAZ | 功能描述:電流型 PWM 控制器 DL SWITCHER W/DRR OPTION 30V CS80 FSC RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6225CAZA | 功能描述:電流型 PWM 控制器 W/ANNEAL DL SWITCHER W/DRR OPTION 30V RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6225CAZA-T | 功能描述:電流型 PWM 控制器 W/ANNEAL DL SWITCHER W/DRR OPTION 30V RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6225CAZ-T | 功能描述:IC CTRLR DDR DRAM, SDRAM 28QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6226 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Advanced PWM and Linear Power Controller for Portable Applications |
發布緊急采購，3分鐘左右您將得到回復。