- 您現在的位置：買賣IC網 > PDF目錄383143 > ISL6244HR (INTERSIL CORP) Multi-Phase PWM Controller PDF資料下載
參數資料
| 型號： | ISL6244HR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Multi-Phase PWM Controller |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC32 |
| 封裝： | 5 X 5 MM, PLASTIC, MO-220-VHHD, QFN-32 |
| 文件頁數： | 14/25頁 |
| 文件大?。?/td> | 845K |
| 代理商： | ISL6244HR |
14
FN9106.3
December 28, 2004
In most cases, each channel uses the same R
ISEN
value to
sense current. A more complete expression for V
DROOP
is
derived by combining equations 15 and 16.
Droop is an optional feature of the ISL6244. If active voltage
positioning is not required, simply leave the IOUT pin open.
REFERENCE OFFSET
Typical microprocessor tolerance windows are centered
around a nominal DAC set point. Implementing a load-line
would require offsetting the output voltage above this
nominal DAC set point, centering the load-line within the
static specification window. The ISL6244 features an internal
100
μ
A current source which feeds out the OFS pin. Placing
a resistor from OFS and ground allows the user to set the
amount of positive offset desired directly to the reference
voltage. The voltage developed across the OFS resistor,
R
OFS
, is divided down internally by a factor of 5 and directly
counters the DAC voltage at the error amplifier non-inverting
input. Select the resistor value based on the voltage offset
desired, V
OFS
, using Equation 19.
μ
A
DYNAMIC VID
Next generation microprocessors can change VID inputs at
any time while the regulator is in operation. The power
management solution is required to monitor the DAC inputs
and respond to VID voltage transitions or ‘on-the-fly’ VID
changes, in a controlled manner, supervising the safe output
voltage transition within the DAC range of the processor
without discontinuity or disruption.
The ISL6244 will register a VID change within 1 to 2 clock
cycles. If the VID change is stable for an additional 1 to 2
clock cycles, the controller will begin executing the output
voltage change. The controller begins incrementing the
reference voltage by making 25mV steps every two
switching cycles until it reaches the new VID code.
The total time required for a VID change, t
DV
, is dependent
on the switching frequency (f
S
), the size of the change
(
VID), and the time before the next switching cycle begins.
Since the ISL6244 recognizes VID-code changes only at the
beginning of switching cycles, up to one full cycle may pass
before a VID change registers. This is followed by a one-
cycle wait before the output voltage begins to change. The
uncertainty in Equation 9 is due to the possibility that the VID
code change may occur between two and four full cycles
before being recognized.
The time required for a converter running with f
S
= 250kHz
to make a 1.2V to 1.4V reference-voltage change is between
72
μ
s and 80
μ
s as calculated using Equation 9. This example
is also illustrated in Figure 7.
Operation Initialization
Before converter operation is initialized, proper conditions
must exist on the enable and disable inputs. Once these
conditions are met, the controller begins a soft-start interval.
Once the output voltage is within the proper window of
operation, the PGOOD output changes state to update an
external system monitor.
Enable and Disable
The PWM outputs are held in a high-impedance state to
assure the drivers remain off while in shutdown mode. Three
separate input conditions must be met before the ISL6244 is
released from shutdown mode.
First, the bias voltage applied at VCC must reach the internal
power-on reset (POR) circuit rising threshold. Once this
threshold is met, proper operation of all aspects of the
ISL6244 is guaranteed. Hysteresis between the rising and
falling thresholds insures that once enabled, the ISL6244 will
not inadvertently turn off unless the bias voltage drops
substantially. See the
Electrical Specifications
for specifics
on POR rising and falling thresholds.
V
DROOP
I
---N
r
ISEN
)
-R
FB
=
(EQ. 7)
R
OFS
5 V
-100
=
(EQ. 8)
2
f
S
----
0.025
1
+
t
DV
2
f
S
----
0.025
2
+
≤
<
(EQ. 9)
FIGURE 19. DYNAMIC-VID WAVEFORMS FOR 250kHz ISL6244
BASED MULTI-PHASE BUCK CONVERTER
15
μ
s/DIV
V
REF
, 100mV/div
V
OUT
, 100mV/div
1.2V
V
ID
, 5V/div
01110
00110
1.2V
VID CHANGE OCCURS
ANYWHERE HERE
ISL6244
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6244CR-T | Multi-Phase PWM Controller |
| ISL6251HRZ-T | Low Cost Multi-Chemistry Battery Charger Controller |
| ISL6251HAZ-T | Low Cost Multi-Chemistry Battery Charger Controller |
| ISL6251AHRZ-T | Low Cost Multi-Chemistry Battery Charger Controller |
| ISL6251 | Octal D-Type Transparent Latches With 3-State Outputs 20-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6244HR-T | 功能描述:IC REG CTRLR BUCK PWM 32-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6244HRZ | 功能描述:電流型 PWM 控制器 VER OF ISL6244HR RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6244HRZ-T | 功能描述:電流型 PWM 控制器 VER OF ISL6244HR-T RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6246C WAF | 制造商:Intersil Corporation 功能描述: |
| ISL6247 6248 WAF | 制造商:Intersil Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。