- 您現在的位置：買賣IC網 > PDF目錄383143 > ISL6251AHRZ (INTERSIL CORP) Low Cost Multi-Chemistry Battery Charger Controller PDF資料下載
參數資料
| 型號： | ISL6251AHRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Low Cost Multi-Chemistry Battery Charger Controller |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC28 |
| 封裝： | LEAD FREE, 5 X 5 MM, PLASTIC, QFN-28 |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 593K |
| 代理商： | ISL6251AHRZ |
13
FN9202.1
June 17, 2005
regulation and current-regulation loops allows for optimal
compensation.
Setting the Battery Charge Current Limit
The CHLIM input sets the maximum charging current. The
current set by the current sense-resistor connects between
CSOP and CSON. The full-scale differential voltage between
CSOP and CSON is 165mV for CHLIM=3.3V, so the
maximum charging current is 4.125A for a
40m
sensing
resistor. Other battery charge current-sense threshold
values can be set by connecting a resistor divider from
VREF or 3.3V to ground,
or by connecting a low impedance
voltage source like a D/A converter in the micro-controller.
The charge current limit threshold is given by:
To set the trickle charge current for the dumb charger, a
resistor in series with a switch Q3 (Figure 12) controlled by
the micro-controller is connected from CHLIM pin to ground.
The trickle charge current is determined by:
When the CHLIM voltage is below 88mV (typical), it will
disable the battery charger. When choosing the current
sensing resistor, note that the voltage drop across the
sensing resistor causes further power dissipation, reducing
efficiency. However, adjusting CHLIM voltage to reduce the
voltage across the current sense resistor R1 will degrade
accuracy due to the smaller signal to the input of the current
sense amplifier. There is a trade-off between accuracy
and
power dissipation. A low pass filter is recommended to
eliminate switching noise. Connect the resistor to the CSOP
pin instead of the CSON pin, as the CSOP pin has lower
bias current and less influence on current-sense accuracy
and voltage regulation accuracy.
Setting the Input Current Limit
The total input current from an AC adapter, or other DC
source, is a function of the system supply current and the
battery-charging current. The input current regulator limits
the input current by reducing the charging current, when the
input current exceeds the input current limit set point.
System current normally fluctuates as portions of the system
are powered up or down. Without input current regulation,
the source must be able to supply the maximum system
current and the maximum charger input current
simultaneously. By using the input current limiter, the current
capability of the AC adapter can be lowered, reducing
system cost.
The ISL6251, ISL6251A limits the battery charge current
when the input current-limit threshold is exceeded, ensuring
the battery charger does not load down the AC adapter
voltage. This constant input current regulation allows the
adapter to fully power the system and prevent the AC
adapter from overloading and crashing the system bus.
An internal amplifier gm3 compares the voltage between
CSIP and CSIN to the input current limit threshold voltage
set by ACLIM. Connect ACLIM to REF, Float and GND for
the full-scale input current limit threshold voltage of 100mV,
75mV and 50mV, respectively, or use a resistor divider from
VREF to ground to set the input current limit as the following
equation:
When choosing the current sense resistor, note that the
voltage drop across this resistor causes further power
dissipation, reducing efficiency. The AC adapter current
sense accuracy is very important. Use a 1% tolerance
current-sense resistor. The highest accuracy of ±3% is
achieved with 100mV current-sense threshold voltage for
ACLIM=VREF, but it has the highest power dissipation. For
example, it has 400mW power dissipation for rated 4A AC
adapter and 1W sensing resistor may have to be used. ±4%
and ±6% accuracy can be achieved with 75mV and 50mV
current-sense threshold voltage for ACLIM=Floating and
ACLIM=GND, respectively.
A low pass filter is suggested to eliminate the switching
noise. Connect the resistor to CSIN pin instead of CSIP pin
because CSIN pin has lower bias current and less influence
on the current-sense accuracy.
AC Adapter Detection
Connect the AC adapter voltage through a resistor divider to
ACSET to detect when AC power is available, as shown in
Figure 12. ACPRN is an open-drain output and is high when
ACSET is less than V
th,rise
, and active low when ACSET is
above V
th,fall
. V
th,rise
and V
th,fall
are given by:
R
V
Where I
hys
is the ACSET input bias current hysteresis and
V
ACSET
= 1.24V (min), 1.26V (typ.) and 1.28V (max.). The
hysteresis is I
hys
R
8
, where I
hys
=2.2μA (min.), 3.4μA (typ.)
and 4.4μA (max.).
TABLE 1. CELL NUMBER PROGRAMMING
CELLS
CELL NUMBER
VDD
4
GND
3
Float
2
I
CHG
1
-------------------
V
---------------------
=
I
CHG
1
-------------------
V
---------------------------------------
=
+
=
050
.
V
VREF
05
.
R
1
I
ACLIM
2
INPUT
ACSET
V
9
8
rise
,
th
1
R
+
=
8
hys
ACSET
9
8
fall
,
th
R
I
V
1
R
R
V
+
=
ISL6251, ISL6251A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6251HAZ | Low Cost Multi-Chemistry Battery Charger Controller |
| ISL6251HRZ | Octal D-Type Transparent Latches With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6251AHAZ | Low Cost Multi-Chemistry Battery Charger Controller |
| ISL6251AHAZ-T | Low Cost Multi-Chemistry Battery Charger Controller |
| ISL6269 | Single Phase PWM Controller for Mobile Graphical Processing Unit (GPU) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6251AHRZ-T | 功能描述:ICBATTERY CHARGER CTRLR 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6251EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL6251 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6251EVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6251 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6251HAZ | 功能描述:IC BATTERY CHARGER CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6251HAZ-T | 功能描述:IC BATTERY CHARGER CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。