- 您現在的位置：買賣IC網 > PDF目錄383143 > ISL6269 (Intersil Corporation) Single Phase PWM Controller for Mobile Graphical Processing Unit (GPU) PDF資料下載
參數資料
| 型號： | ISL6269 |
| 廠商： | Intersil Corporation |
| 英文描述： | Single Phase PWM Controller for Mobile Graphical Processing Unit (GPU) |
| 中文描述： | 單相PWM控制器，移動圖形處理單元（GPU） |
| 文件頁數： | 5/17頁 |
| 文件大?。?/td> | 395K |
| 代理商： | ISL6269 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
5
FN9177.0
June 14, 2005
Functional Pin Descriptions
GND Pin
Bottom terminal pad of QFN package
Signal common of the IC. Unless otherwise stated, signals
are referenced to the GND pin, not the PGND pin.
VIN Pin-1 (Input)
The VIN pin measures the converter input voltage with
respect to the GND pin. VIN is a required input to the R
3
PWM modulator. The VIN pin is also the input source for the
integrated +5V LDO regulator.
VCC Pin-2 (Output)
The VCC pin is the output of the integrated +5V LDO
regulator, which provides the bias voltage for the IC. The
VCC pin delivers regulated +5V whenever the EN pin is
pulled above V
ENTHR
. For best performance the LDO
requires at least a 1μF MLCC decouple capacitor to the
GND pin.
FCCM Pin-3 (Logic)
The FCCM pin configures the controller to operate in forced-
continuous-conduction-mode (FCCM) or diode-emulation-
mode (DEM.) DEM is disabled when the FCCM pin is pulled
above the rising threshold voltage V
FCCMTHR
, and DEM is
enabled when the FCCM pin is pulled below the falling
threshold voltage V
FCCMTHF.
EN Pin-4 (Logic)
The EN pin is the on/off switch of the IC. When the EN pin is
pulled above the rising threshold voltage V
ENTHR,
V
CC
will
ramp up and begin regulation. The soft-start sequence
begins once V
CC
ramps above the power-on reset (POR)
rising threshold voltage V
CCTHR
. When the EN pin is pulled
below the falling threshold voltage V
ENTHF
, PWM
immediately stops and V
CC
decays below the POR falling
threshold voltage V
CCTHF
, at which time the IC turns off.
COMP Pin-5 (Signal)
The COMP pin is the output of the control-loop error
amplifier. Loop compensation components connect from the
COMP pin to the FB pin.
FB Pin-6 (Signal)
The FB pin is the inverting input of the control loop error
amplifier. The converter will regulate to 600mV at the FB pin
with respect to the GND pin. Scale the desired output
voltage to 600mV with a voltage divider network made from
resistors R
TOP
and R
BOTTOM
. Loop compensation
components connect from the FB pin to the COMP pin.
FSET Pin-7 (Signal)
The FSET pin programs the PWM switching frequency of the
converter. Connect a resistor R
FSET
and a 10nF capacitor
C
FSET
from the FSET pin to the GND pin.
VO Pin-8 (Input)
The VO pin makes a direct measurement of the converter
output voltage used exclusively by the R
3
PWM modulator.
The VO pin should be connected to the top of feedback
resistor R
TOP
at the converter output. Refer to Figure
1,
Typical Application Schematic.
ISEN Pin-9 (Input)
The ISEN pin is the input to the overcurrent protection (OCP)
and short-circuit protection (SCP) circuits. Connect a resistor
R
SEN
between the ISEN pin and the PHASE pin. Select the
value of R
SEN
that will force the ISEN pin to source the I
SEN
threshold current I
OC
when the peak inductor current
reaches the desired OCP setpoint. The SCP threshold
current I
SC
is fixed at twice the OCP threshold current I
OC
PGND Pin-10
The PGND pin should be connected to the source of the low-
side MOSFET, preferably with an isolated path that is in
parallel with the trace connecting the LG pin to the gate of
the MOSFET. The PGND pin is an isolated path used
exclusively to conduct the turn-off transient current that flows
out the PGND pin, through the gate-source capacitance of
the low-side MOSFET, into the LG pin, and back to the
PGND pin through the pull-down resistance of the LG driver.
The adaptive shoot-through protection circuit, measures the
low-side MOSFET gate voltage with respect to the PGND
pin, not the GND pin.
LG Pin-11 (Output)
The LG pin is the output of the low-side MOSFET gate
driver. Connect to the gate of the low-side MOSFET.
PVCC Pin-12 (Input)
The PVCC pin is the input voltage for the low-side MOSFET
gate driver LG. Connect a +5V power source to the PVCC
pin with respect to the GND pin, a 1μF MLCC bypass
capacitor needs to be connected from the PVCC pin to the
PGND pin, not the GND pin. The VCC output may be used
for the PVCC input voltage source. Connect the VCC pin to
the PVCC pin through a low-pass filter consisting of a
resistor and the PVCC bypass capacitor. Refer to Figure
1,
Typical Application Schematic
.
ISL6269
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6269CRZ | Single Phase PWM Controller for Mobile Graphical Processing Unit (GPU) |
| ISL6269CRZ-T | Single Phase PWM Controller for Mobile Graphical Processing Unit (GPU) |
| ISL6291-2CRTR5155 | IC OPAMP DUAL 18V DIP8 |
| ISL6291-2CRZTR5155 | Li-ion/Li Polymer Linear Battery Charger |
| ISL6291-2CRZTR5155-T | Li-ion/Li Polymer Linear Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6269_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High-Performance Notebook PWM Controller with Bias Regulator and Audio-Frequency Clamp |
| ISL6269A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High-Performance Notebook PWM Controller |
| ISL6269ACRZ | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6269ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6269ACRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6269ACRZ-T WITH GOLD BOND WIRE ONLY, T&R - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。