- 您現在的位置：買賣IC網 > PDF目錄383143 > ISL6269CRZ-T (INTERSIL CORP) Single Phase PWM Controller for Mobile Graphical Processing Unit (GPU) PDF資料下載
參數資料
| 型號： | ISL6269CRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Single Phase PWM Controller for Mobile Graphical Processing Unit (GPU) |
| 中文描述： | SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 4 X 4 MM, ROHS COMPLIANT, PLASTIC, MO-220-VGGC, QFN-16 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 395K |
| 代理商： | ISL6269CRZ-T |
15
FN9177.0
June 14, 2005
Pin 5 (COMP)
The loop compensation components connect from the
COMP pin to the FB pin. Place the components close to the
FB pin to make the traces as short as possible.
Pin 6 (FB)
There is usually a resistor divider connecting the output
voltage of the converter to the FB pin. The correct layout
should bring the output voltage from the regulation point to
the FB pin with kelvin traces. The input impedance of the FB
pin is high, so place the resistor divider close to the pin,
keeping the high impedance trace short.
Pin 7 (FSET)
This pin requires a quiet environment. The resistor R
FSET
and capacitor C
FSET
should be placed directly adjacent to
this pin. Keep fast moving nodes away from this pin.
Pin 8 (VO)
The VO pin should be connected to the Kelvin traces at the
FB voltage divider.
Pin 9 (ISEN)
The ISEN trace should be routed away from the traces and
components connected to the FB pin, COMP pin, and FSET
pin.
Pin 10 (PGND)
This is the pull-down return path for the LG low-side
MOSFET gate drive. This should be an isolated low-
resistance, low-inductance trace that connects to the source
of the low-side MOSFET.
Pin 11 (LG)
Connect to the gate terminal of the low-side MOSFET. The
signal going through this trace is both high dv/dt and high
di/dt, with high peak charging and discharging current. Route
this trace in parallel with the trace from the PGND pin. These
two traces should be short, wide, and away from other
traces. There should be no other weak signal traces in
parallel with these traces on any layer.
Pin 12 (PVCC)
A ceramic decoupling capacitor connects from the PVCC pin
to the PGND pin, not the GND pin. Closely place the
capacitor on the same side of the board as the ISL6269 IC.
Pin 13 (BOOT)
The di/dt and dv/dt of this pin are as high as that of the LG
pin, UG pin, and the PHASE pin; therefore, the traces should
be as short as possible.
Pin 14 (UG)
Connect to the gate terminal of the high-side MOSFET. The
signal going through this trace is both high dv/dt and high
di/dt, with high peak charging and discharging current. Route
this trace in parallel with the trace from the PHASE pin.
These two traces should be short, wide, and away from
other traces. There should be no other weak signal traces in
parallel with these traces on any layer.
Pin 15 (PHASE)
Connect to the low-side MOSFET drain terminal. The phase
node has a very high dv/dt with a voltage swing from the input
voltage to ground. This trace should be short, and positioned
away from other weak signal traces.
Pin 16 (PGOOD)
A very robust pin. Treat as a typical logic signal.
Copper Size for the Phase Node
The parasitic capacitance and parasitic inductance of the
phase node should be kept very low to minimize ringing. If
ringing is excessive, it could easily affect current sample
information. It would be best to limit the size of the PHASE
node copper in strict accordance with the current and
thermal management of the application.
Identify the Power and Signal Ground
The input and output capacitors of the converter, the source
terminal of the low-side MOSFET, and the PGND pin should
be closely connected to the power ground. The other
components should connect to signal ground. Signal and
power ground are tied together at the negative terminal of
the output capacitors.
Decoupling Capacitor for Switching MOSFET
Ceramic capacitors should be closely connected to the drain
side of the high-side MOSFET, and the source of the low-
side MOSFET. This capacitor reduces the amplitude of the
turn-off voltage spike.
Control Loop
The control loop model of the ISL6269 is partitioned into
function blocks consisting of:
- The Duty cycle to Vo transfer function G
vd
(s) which is
determined by the value of the output power
components, input voltage, and output voltage.
- The Vcomp to Duty cycle transfer function F
m
(s) which
is determined by the PWM frequency, input voltage,
output voltage, resistor R
FSET
, and capacitor C
FSET.
- The product of the G
vd
(s) and F
m
(s) transfer functions
is expressed as the Vcomp to Vo transfer function
G
vovc
(s).
- The type-two compensation network G
comp
(s) that
connects across the COMP and FB pins.
- The product of the G
comp
(s) and G
vovc
(s) transfer
functions is expressed as the loop transfer function T(s).
ISL6269
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6291-2CRTR5155 | IC OPAMP DUAL 18V DIP8 |
| ISL6291-2CRZTR5155 | Li-ion/Li Polymer Linear Battery Charger |
| ISL6291-2CRZTR5155-T | Li-ion/Li Polymer Linear Battery Charger |
| ISL6291-1CR-T | Li-ion/Li Polymer Linear Battery Charger |
| ISL6291-2CRTR5155-T | Li-ion/Li Polymer Linear Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6269EVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6269 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6269IRZ | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6269IRZ-T | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6271A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Integrated XScale Regulator |
| ISL6271ACR | 功能描述:IC REG PMIC 1BUCK 2LDO 20-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。