參數資料
型號： ISL6292D
廠商： Intersil Corporation
英文描述： Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85
中文描述： Li-ion/Li聚合物電池充電器
文件頁數： 12/13頁
文件大?。?/td> 461K
代理商： ISL6292D
12
Shutdown
The ISL6292D can be shutdown by pulling the EN pin to
ground. When shut down, the charger draws typically less
than 30
μ
A current from the input power and the 2.8V output
at the V2P8 pin is also turned off. The EN pin needs be
driven with an open-drain or open-collector logic output, so
that the EN pin is floating when the charger is enabled.
Input and Output Capacitor Selection
Typically any type of capacitors can be used for the input
and the output. A 0.47
μ
F or higher value ceramic capacitor
for the input is recommended to be placed very close to the
input pin and the ground pin. Another 10
μ
F capacitance is
required to stabilize the input voltage. When the battery is
attached to the charger, the output capacitor can be any
ceramic type with the value higher than 0.1
μ
F. However, if
there is a chance the charger will be used as an LDO linear
regulator, a 10
μ
F tantalum capacitor is recommended.
Working with Current-Limited Adapter
The ISL6292D can work with a current-limited adapter to
significantly reduce the thermal dissipation during charging.
Refer to the ISL6292 datasheet, which can be found at
http://www.intersil.com, for more details.
Board Layout Recommendations
The ISL6292D internal thermal foldback function limits the
charge current when the internal temperature reaches
approximately 100°C. In order to maximize the current
capability, it is very important that the exposed pad under the
package is properly soldered to the board and is connected
to other layers through thermal vias. More thermal vias and
more copper attached to the exposed pad will result in better
thermal performance. On the other hand, the number of vias
is limited by the size of the pad. The exposed pads for the
4x4 QFN package is able to have 5 vias. Refer to the
ISL6292 evaluation boards for layout examples.
TABLE 1. SUMMARY OF CHARGE STATUS AND LED OUTPUT
STATUS
LED OUTPUT
Charging
On
Charge Completed or Disabled
OFF
Temperature Fault
Blinks at the speed of T
9th
TIMEOUT Fault
Blinks at the speed of T
8th
TABLE 2. SUMMARY OF CHARGE STATUS AND LED OUTPUT
STATUS
LED OUTPUT
Charging
On
Charge Completed or Disabled
OFF
Fault
Blinks at the speed of T
8th
ISL6292D
相關PDF資料
PDF描述
ISL6292DCR4-T Li-ion/Li Polymer Battery Charger
ISL6292DCRZ Li-ion/Li Polymer Battery Charger
ISL6295CV-T Low Voltage Fuel Gauge
ISL6295 Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85
ISL6295CV Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85
相關代理商/技術參數
參數描述
ISL6292DCR4 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger
ISL6292DCR4-T 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger
ISL6292DCRZ 功能描述:電池管理 LINEAR SINGLE CELL LI-ION CHRGR 16LD RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
ISL6292DCRZ-T 功能描述:電池管理 LINEAR SINGLE CELL LI-ION CHRGR 16LD RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
ISL6292EVAL1 功能描述:EVALUATION BOARD 1 ISL6292 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*