- 您現在的位置：買賣IC網 > PDF目錄383144 > ISL6292D (Intersil Corporation) Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6292D |
| 廠商： | Intersil Corporation |
| 英文描述： | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| 中文描述： | Li-ion/Li聚合物電池充電器 |
| 文件頁數： | 13/13頁 |
| 文件大?。?/td> | 461K |
| 代理商： | ISL6292D |
13
ISL6292D
Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
L16.4x4
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
(COMPLIANT TO JEDEC MO-220-VGGC ISSUE C)
SYMBOL
MILLIMETERS
NOTES
MIN
NOMINAL
MAX
A
0.80
0.90
1.00
-
A1
-
-
0.05
-
A2
-
-
1.00
9
A3
0.20 REF
9
b
0.23
0.28
0.35
5, 8
D
4.00 BSC
-
D1
3.75 BSC
9
D2
1.95
2.10
2.25
7, 8
E
4.00 BSC
-
E1
3.75 BSC
9
E2
1.95
2.10
2.25
7, 8
e
0.65 BSC
-
k
0.25
-
-
-
L
0.50
0.60
0.75
8
L1
-
-
0.15
10
N
16
2
Nd
4
3
Ne
4
3
P
-
-
0.60
9
θ
-
-
12
9
Rev. 5 5/04
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
8. Nominal dimensions are provided to assist with PCB Land Pattern
Design efforts, see Intersil Technical Brief TB389.
9. Features and dimensions A2, A3, D1, E1, P &
θ
are present when
Anvil singulation method is used and not present for saw
singulation.
10. Depending on the method of lead termination at the edge of the
package, a maximum 0.15mm pull back (L1) maybe present. L
minus L1 to be equal to or greater than 0.3mm.
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6292DCR4-T | Li-ion/Li Polymer Battery Charger |
| ISL6292DCRZ | Li-ion/Li Polymer Battery Charger |
| ISL6295CV-T | Low Voltage Fuel Gauge |
| ISL6295 | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
| ISL6295CV | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6292DCR4 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292DCR4-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
| ISL6292DCRZ | 功能描述:電池管理 LINEAR SINGLE CELL LI-ION CHRGR 16LD RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| ISL6292DCRZ-T | 功能描述:電池管理 LINEAR SINGLE CELL LI-ION CHRGR 16LD RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| ISL6292EVAL1 | 功能描述:EVALUATION BOARD 1 ISL6292 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
發布緊急采購，3分鐘左右您將得到回復。