- 您現在的位置：買賣IC網 > PDF目錄383145 > ISL6308CRZ-T (INTERSIL CORP) Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6308CRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220VJJD-1, QFN-40 |
| 文件頁數： | 8/27頁 |
| 文件大?。?/td> | 765K |
| 代理商： | ISL6308CRZ-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
8
FN9208.2
October 19, 2005
REF0 and REF1 (Pins 40, 39)
These pins make up the 2-bit input that selects the fixed
DAC reference voltage. These pins respond to TTL logic
thresholds. The ISL6308 decodes these inputs to establish
one of four fixed reference voltages; see “Table 1” for
correspondence between REF0 and REF1 inputs and
reference voltage settings.
These pins are internally pulled high, to approximately 1.2V,
by 40μA (typically) internal current sources; the internal pull-
up current decreases to 0 as the REF0 and REF1 voltages
approach the internal pull-up voltage. Both REF0 and REF1
pins are compatible with external pull-up voltages not
exceeding the IC’s bias voltage (VCC).
RGND and VSEN (Pins 10, 11)
RGND and VSEN are inputs to the precision differential
remote-sense amplifier and should be connected to the
sense pins of the remote load.
ICOMP, ISUM, and IREF (Pins 13, 15, 16)
ISUM, IREF, and ICOMP are the DCR current sense
amplifier’s negative input, positive input, and output
respectively. For accurate DCR current sensing, connect a
resistor from each channel’s phase node to ISUM and
connect IREF to the summing point of the output inductors.
A parallel R-C feedback circuit connected between ISUM
and ICOMP will then create a voltage from IREF to ICOMP
proportional to the voltage drop across the inductor DCR.
This voltage is referred to as the droop voltage and is added
to the differential remote-sense amplifier’s output.
An optional 0.001-0.01μF ceramic capacitor can be placed
from the IREF pin to the ISUM pin to help reduce common
mode noise that might be introduced by the layout.
DROOP (Pin 14)
This pin enables or disables droop. Tie this pin to the ICOMP
pin to enable droop. To disable droop, tie this pin to the IREF
pin.
VDIFF (Pin 9)
VDIFF is the output of the differential remote-sense
amplifier. The voltage on this pin is equal to the difference
between VSEN and RGND added to the difference between
IREF and ICOMP. VDIFF therefore represents the VOUT
voltage plus the droop voltage.
FB and COMP (Pin 7, 8)
The internal error amplifier’s inverting input and output
respectively. FB is connected to VDIFF through an external
R or R-C network depending on the desired type of
compensation (Type II or III). COMP is tied back to FB
through an external R-C network to compensate the
regulator.
DAC (Pin 3)
The DAC pin is the direct output of the internal DAC. This pin
is connected to the REF pin using a 1-5k
resistor. This pin
can be left open if an external reference is used.
REF (Pin 4)
The REF input pin is the positive input of the error amplifier.
This pin can be connected to the DAC pin using a resistor
(1-5k
) when the internal DAC voltage is used as the
reference voltage. When an external voltage reference is
used, it must be connected directly to the REF pin, while the
DAC pin is left unconnected. The output voltage will be
regulated to the voltage at the REF pin unless this voltage
is greater than the voltage at the DAC pin. If an external
reference is used at this pin, its magnitude cannot exceed
1.75V.
A capacitor is used between the REF pin and ground to
smooth the DAC voltage during soft-start.
OFST (Pin 5)
The OFST pin provides a means to program a DC current for
generating an offset voltage across the resistor between FB
and VDIFF. The offset current is generated via an external
resistor and precision internal voltage references. The
polarity of the offset is selected by connecting the resistor to
GND or VCC. For no offset, the OFST pin should be left
unconnected.
OCSET (Pin 12)
This is the overcurrent set pin. Placing a resistor from OCSET
to ICOMP, allows a 100μA current to flow out of this pin,
producing a voltage reference. Internal circuitry compares the
voltage at OCSET to the voltage at ISUM, and if ISUM ever
exceeds OCSET, the overcurrent protection activates.
ISEN1, ISEN2 and ISEN3 (Pins 32, 25, 19)
These pins are used for balancing the channel currents by
sensing the current through each channel’s lower MOSFET
when it is conducting. Connect a resistor between the
ISEN1, ISEN2, and ISEN3 pins and their respective phase
node. This resistor sets a current proportional to the current
in the lower MOSFET during its conduction interval.
UGATE1, UGATE2, and UGATE3 (Pins 31, 27, 20)
Connect these pins to the upper MOSFETs’ gates. These
pins are used to control the upper MOSFETs and are
monitored for shoot-through prevention purposes. Maximum
individual channel duty cycle is limited to 66%.
BOOT1, BOOT2, and BOOT3 (Pins 30, 26, 21)
These pins provide the bias voltage for the upper MOSFETs’
drives. Connect these pins to appropriately-chosen external
bootstrap capacitors. Internal bootstrap diodes connected to
the PVCC pins provide the necessary bootstrap charge.
PHASE1, PHASE2, and PHASE3 (Pins 29, 28, 22)
Connect these pins to the sources of the upper MOSFETs.
These pins are the return path for the upper MOSFETs’
drives.
ISL6308
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6308IRZ-T | Three-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| ISL6315 | Two-Phase Multiphase Buck PWM Controller with Integrated MOSFET Drivers(帶集成MOSFET驅動器的雙相降壓PWM控制器) |
| ISL6316 | Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 |
| ISL6316IRZ | MINIATURE TOGGLE SWITCH |
| ISL6316CRZ | Enhanced 4-Phase PWM Controller with 6-Bit VID Code Capable of Precision RDS(ON) or DCR Differential Current Sensing for VR10 Application |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6308CRZ-TR5374 | 制造商:Intersil Corporation 功能描述:ISL6308CRZ W/ 24HR BURN-IN - Tape and Reel 制造商:Intersil Corporation 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN 制造商:Intersil 功能描述:ISL6308CRZ W/24HRU RN-IN |
| ISL6308CRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6308CRZ-T W/GOLD BOND WIRE ONLY - Tape and Reel |
| ISL6308EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL6308 EVALUATION BOARD 1 - ROHS COMPLIANT - QFN - Bulk |
| ISL6308IRZ | 功能描述:電壓模式 PWM 控制器 DAC-LESS MULTI-PHS PWM CNTRLR W/3-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6308IRZ-T | 功能描述:電壓模式 PWM 控制器 DAC-LESS MULTI-PHS PWM CNTRLR W/3-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。