參數資料
型號： ISL6310EVAL1
廠商： Intersil Corporation
英文描述： Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver
中文描述： 兩相降壓PWM控制器，帶有高電流集成MOSFET驅動器
文件頁數： 15/27頁
文件大?。?/td> 711K
代理商： ISL6310EVAL1
15
FN9209.2
October 19, 2005
2. The voltage on ENLL must be above 0.66V. The EN input
allows for power sequencing between the controller bias
voltage and another voltage rail. The enable comparator
holds the ISL6310 in shutdown until the voltage at ENLL
rises above 0.66V. The enable comparator has 100mV of
hysteresis to prevent bounce.
3. The driver bias voltage applied at the PVCC pins must
reach the internal power-on reset (POR) rising threshold.
In order for the ISL6310 to begin operation, PVCC is the
only pin that is required to have a voltage applied that
exceeds POR. Hysteresis between the rising and falling
thresholds assure that once enabled, the ISL6310 will not
inadvertently turn off unless the PVCC bias voltage drops
substantially (see
Electrical Specifications
).
When each of these conditions is true, the controller
immediately begins the soft-start sequence.
Soft-Start
During soft-start, the DAC voltage ramps linearly from zero
to the programmed level. The PWM signals remain in the
high-impedance state until the controller detects that the
ramping DAC level has reached the output-voltage level.
This protects the system against the large, negative inductor
currents that would otherwise occur when starting with a pre-
existing charge on the output as the controller attempted to
regulate to zero volts at the beginning of the soft-start cycle.
The Output soft-start time, T
SS
, begins with a delay period
equal to 64 switching cycles after the ENLL has exceeded its
POR level, followed by a linear ramp with a rate determined
by the switching period, 1/F
SW
.
For example, a regulator with 450kHz switching frequency
having REF voltage set to 1.2V has T
SS
equal to 3.55ms.
A 100mV offset exists on the remote-sense amplifier at the
beginning of soft-start and ramps to zero during the first 640
cycles of soft-start (704 cycles following enable). This
prevents the large inrush current that would otherwise occur
should the output voltage start out with a slight negative
bias.
During the first 640 cycles of soft-start (704 cycles following
enable) the DAC voltage increments the reference in 25mV
steps. The remainder of soft-start sees the DAC ramping
with 12.5mV steps.
The ISL6310 also has the ability to start up into a pre-
charged output as shown in Figure 12, without causing any
unnecessary disturbance. The FB pin is monitored during
soft-start, and should it be higher than the equivalent internal
ramping reference voltage, the output drives hold both
MOSFETs off. Once the internal ramping reference exceeds
the FB pin potential, the output drives are enabled, allowing
the output to ramp from the pre-charged level to the final
level dictated by the reference setting. Should the output be
pre-charged to a level exceeding the reference setting, the
output drives are enabled at the end of the soft-start period,
leading to an abrupt correction in the output voltage down to
the “reference set” level.
Fault Monitoring and Protection
The ISL6310 actively monitors output voltage and current to
detect fault conditions. Fault monitors trigger protective
measures to prevent damage to the sensitive load. One
common power good indicator is provided for linking to
external system monitors. The schematic in Figure 13
outlines the interaction between the fault monitors and the
power good signal.
FIGURE 11. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (ENLL) FUNCTION
-
+
0.66V
EXTERNAL CIRCUIT
ISL6310 INTERNAL CIRCUIT
ENLL
+12V
POR
CIRCUIT
10.7k
1.40k
ENABLE
COMPARATOR
SOFT-START
AND
FAULT LOGIC
VCC
PVCC
T
SS
--------+
SW
1280
=
(EQ. 12)
FIGURE 12. SOFT-START WAVEFORMS FOR ISL6310-BASED
MULTI-PHASE CONVERTER
ENLL (5V/DIV)
V
OUT
(0.5V/DIV)
GND>
T1
GND>
T2
T3
OUTPUT PRECHARGED
BELOW DAC LEVEL
OUTPUT PRECHARGED
ABOVE DAC LEVEL
ISL6310
相關PDF資料
PDF描述
ISL6310IRZ Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver
ISL6431A Advanced Pulse Width Modulation (PWM) Controller for Broadband Applications
ISL6431ACB Advanced Pulse Width Modulation (PWM) Controller for Broadband Applications
ISL6520A Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 125
ISL6525CBZ Buck and Synchronous-Rectifier Pulse-Width Modulator (PWM) Controller
相關代理商/技術參數
參數描述
ISL6310EVAL1Z 功能描述:EVALUATION BOARD FOR ISL6310 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ISL6310IRZ 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTROL W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
ISL6310IRZ-T 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTROL W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
ISL6312ACRZ 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
ISL6312ACRZ-T 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*