參數資料
型號： ISL6524CBZA-T
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： VRM8.5 PWM and Triple Linear Power System Controller
中文描述： SWITCHING CONTROLLER, 215 kHz SWITCHING FREQ-MAX, PDSO28
封裝： ROHS COMPLIANT, PLASTIC, MS-013-AE, SOIC-28
文件頁數： 10/16頁
文件大?。?/td> 445K
代理商： ISL6524CBZA-T
10
FN9015.3
April 18, 2005
Application Guidelines
Soft-Start Interval
Initially, the soft-start function clamps the error amplifier’s output
of the PWM converter. This generates PHASE pulses of
increasing width that charge the output capacitor(s). The
resulting output voltages start-up as shown in Figure 6.
The soft-start function controls the output voltage rate of rise
to limit the current surge at start-up. The soft-start interval
and the surge current are programmed by the soft-start
capacitor, C
SS
. Programming a faster soft-start interval
increases the peak surge current. Using the recommended
0.1mF soft start capacitors ensure all output voltages ramp
up to their set values in a quick and controlled fashion, while
meeting the system timing requirements.
Shutdown
The PWM output does not switch until the soft-start voltage
(V
SS13
) exceeds the oscillator’s valley voltage. Additionally,
the reference on each linear’s amplifier is clamped to the soft-
start voltage. Holding the SS24 pin low (with an open drain or
open collector signal) turns off regulators 1, 2 and 3.
Regulator 4 (MCH) will simply drop its output to the
intermediate soft-start level. This output is not allowed to
violate the 2V maximum potential gap to the ATX 3.3V output.
Layout Considerations
MOSFETs switch very fast and efficiently. The speed with
which the current transitions from one device to another
causes voltage spikes across the interconnecting
impedances and parasitic circuit elements. The voltage
spikes can degrade efficiency, radiate noise into the circuit,
and lead to device overvoltage stress. Careful component
layout and printed circuit design minimizes the voltage
spikes in the converter. Consider, as an example, the turn-off
transition of the upper MOSFET. Prior to turn-off, the upper
MOSFET was carrying the full load current. During the turn-
off, current stops flowing in the upper MOSFET and is picked
up by the lower MOSFET or Schottky diode. Any inductance
in the switched current path generates a large voltage spike
during the switching interval. Careful component selection,
tight layout of the critical components, and short, wide circuit
traces minimize the magnitude of voltage spikes.
There are two sets of critical components in a DC-DC
converter using an ISL6524 controller. The switching power
components are the most critical because they switch large
amounts of energy, and as such, they tend to generate
equally large amounts of noise. The critical small signal
components are those connected to sensitive nodes or
those supplying critical bypass current.
The power components and the controller IC should be
placed first. Locate the input capacitors, especially the high-
frequency ceramic decoupling capacitors, close to the power
switches. Locate the output inductor and output capacitors
between the MOSFETs and the load. Locate the PWM
controller close to the MOSFETs.
The critical small signal components include the bypass
capacitor for VCC and the soft-start capacitor, C
SS
. Locate
these components close to their connecting pins on the
control IC. Minimize any leakage current paths from any SS
node, since the internal current source is only 28mA.
A multi-layer printed circuit board is recommended. Figure
10 shows the connections of the critical components in the
converter. Note that the capacitors C
IN
and C
OUT
each
could represent numerous physical capacitors. Dedicate one
solid layer for a ground plane and make all critical
component ground connections with vias to this layer.
TABLE 1. OUT1 OUTPUT VOLTAGE PROGRAM
PIN NAME
NOMINAL
DACOUT
VOLTAGE
VID3
VID2
VID1
VID0
VID25
0
1
0
0
0
1.050
0
1
0
0
1
1.075
0
0
1
1
0
1.100
0
0
1
1
1
1.125
0
0
1
0
0
1.150
0
0
1
0
1
1.175
0
0
0
1
0
1.200
0
0
0
1
1
1.225
0
0
0
0
0
1.250
0
0
0
0
1
1.275
1
1
1
1
0
1.300
1
1
1
1
1
1.325
1
1
1
0
0
1.350
1
1
1
0
1
1.375
1
1
0
1
0
1.400
1
1
0
1
1
1.425
1
1
0
0
0
1.450
1
1
0
0
1
1.475
1
0
1
1
0
1.500
1
0
1
1
1
1.525
1
0
1
0
0
1.550
1
0
1
0
1
1.575
1
0
0
1
0
1.600
1
0
0
1
1
1.625
1
0
0
0
0
1.650
1
0
0
0
1
1.675
0
1
1
1
0
1.700
0
1
1
1
1
1.725
0
1
1
0
0
1.750
0
1
1
0
1
1.775
0
1
0
1
0
1.800
0
1
0
1
1
1.825
NOTE: 0 = connected to GND, 1 = open or connected to 3.3V
through pull-up resistors
相關PDF資料
PDF描述
ISL6524 Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 85
ISL6524ACB-T VRM8.5 PWM and Triple Linear Power System Controller
ISL6524EVAL1 VRM8.5 PWM and Triple Linear Power System Controller
ISL6526IRZ-T RX-1M Hi-Meg Resistor, Ultra-high resistance, High stability, Hermetically Sealed, 0.5 W Rating
ISL6526CR-T Single Synchronous Buck Pulse-Width Modulation (PWM) Controller
相關代理商/技術參數
參數描述
ISL6524CBZ-T 功能描述:IC CTLR VRM8.5 PWM TRPL 28-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR)
ISL6524EVAL1 功能描述:EVALUATION BOARD VRM8.5 ISL6524 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ISL6525CB 功能描述:IC REG CTRLR BUCK PWM VM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR)
ISL6525CB-T 功能描述:IC REG CTRLR BUCK PWM VM 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR)
ISL6525CBZ 功能描述:電壓模式 PWM 控制器 VTT REG FORVRM 8.5 1 4LD RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*