- 您現在的位置：買賣IC網 > PDF目錄383155 > ISL6545EVAL1 (Intersil Corporation) 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller PDF資料下載
參數資料
| 型號： | ISL6545EVAL1 |
| 廠商： | Intersil Corporation |
| 英文描述： | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| 中文描述： | 單5V或12V同步降壓脈寬調制（PWM）控制器 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 302K |
| 代理商： | ISL6545EVAL1 |
www.DataSheet4U.com
12
FN6305.3
November 15, 2006
which is not shown. Using the above guidelines should yield a
compensation gain similar to the curve plotted. The open loop
error amplifier gain bounds the compensation gain. Check the
compensation gain at F
P2
against the capabilities of the error
amplifier. The closed loop gain, G
CL
, is constructed on the log-
log graph of Figure 10 by adding the modulator gain, G
MOD
(in
dB), to the feedback compensation gain, G
FB
(in dB). This is
equivalent to multiplying the modulator transfer function and the
compensation transfer function and then plotting the resulting
gain.
A stable control loop has a gain crossing with close to a
-20dB/decade slope and a phase margin greater than 45°.
Include worst case component variations when determining
phase margin. The mathematical model presented makes a
number of approximations and is generally not accurate at
frequencies approaching or exceeding half the switching
frequency. When designing compensation networks, select
target crossover frequencies in the range of 10% to 30% of
the switching frequency, F
SW
.
This is just one method to calculate compensation
components; there are variations of the above equations.
The error amp is similar to that on other Intersil regulators,
so existing tools can be used here as well. Special
consideration is needed if the size of a ceramic output
capacitance in parallel with bulk capacitors gets too large;
the calculation needs to model them both separately
(attempting to combine two different capacitors types into
one composite component model may not work properly; a
special tool may be needed; contact your local Intersil
person for assistance).
Component Selection Guidelines
Output Capacitor Selection
An output capacitor is required to filter the output and supply
the load transient current. The filtering requirements are a
function of the switching frequency and the ripple current.
The load transient requirements are a function of the slew
rate (di/dt) and the magnitude of the transient load current.
These requirements are generally met with a mix of
capacitors and careful layout.
Modern components and loads are capable of producing
transient load rates above 1A/ns. High frequency capacitors
initially supply the transient and slow the current load rate
seen by the bulk capacitors. The bulk filter capacitor values
are generally determined by the ESR (Effective Series
Resistance) and voltage rating requirements rather than
actual capacitance requirements.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications for the bulk capacitors. The
bulk capacitor’s ESR will determine the output ripple voltage
and the initial voltage drop after a high slew-rate transient. An
aluminum electrolytic capacitor’s ESR value is related to the
case size with lower ESR available in larger case sizes.
However, the Equivalent Series Inductance (ESL) of these
capacitors increases with case size and can reduce the
usefulness of the capacitor to high slew-rate transient loading.
Unfortunately, ESL is not a specified parameter. Work with
your capacitor supplier and measure the capacitor’s
impedance with frequency to select a suitable component. In
most cases, multiple electrolytic capacitors of small case size
perform better than a single large case capacitor.
Output Inductor Selection
The output inductor is selected to meet the output voltage
ripple requirements and minimize the converter’s response
time to the load transient. The inductor value determines the
converter’s ripple current and the ripple voltage is a function
of the ripple current. The ripple voltage and current are
approximated by the following equations:
Increasing the value of inductance reduces the ripple current
and voltage. However, the large inductance values reduce
the converter’s response time to a load transient.
One of the parameters limiting the converter’s response to
a load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6545 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
required to slew the inductor current from an initial current
value to the transient current level. During this interval the
difference between the inductor current and the transient
0
F
P1
F
Z2
OPEN LOOP E/A GAIN
F
Z1
F
P2
F
LC
F
CE
COMPENSATION GAIN
CLOSED LOOP GAIN
G
FREQUENCY
MODULATOR GAIN
FIGURE 10. ASYMPTOTIC BODE PLOT OF CONVERTER GAIN
20
d
OSC
V
IN
----V
log
20
R1
log
LOG
L
F
0
G
MOD
G
FB
G
CL
Δ
I
=
V
IN
- V
OUT
Fsw x L
V
OUT
V
IN
Δ
V
OUT
=
Δ
I
x
ESR
x
ISL6545, ISL6545A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6545IBZ | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6545IRZ | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6548ACRZA-T | ACPI Regulator/Controller for Dual Channel DDR Memory Systems |
| ISL6548A | 500-mA Peak Step-Up, Step-Down, Inverting Switching Voltage Regulator 14-PDIP 0 to 70 |
| ISL6548ACRZ | 500-mA Peak Step-Up, Step-Down, Inverting Switching Voltage Regulator 14-PDIP 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6545IBZ | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:75 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.3 V ~ 13.5 V 降壓:是 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:0°C ~ 70°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:管件 產品目錄頁面:1051 (CN2011-ZH PDF) 其它名稱:296-2543-5 |
| ISL6545IBZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| ISL6545IRZ | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6545IRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6546IRZ | 功能描述:IC REG BUCK SYNC 1.2A 10-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
發布緊急采購，3分鐘左右您將得到回復。