- 您現在的位置：買賣IC網 > PDF目錄383156 > ISL6556BCRZ (INTERSIL CORP) Optimized Multi-Phase PWM Controller with 6-Bit DAC and Programmable Internal Temperature Compensation for VR10.X Application PDF資料下載
參數資料
| 型號： | ISL6556BCRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Optimized Multi-Phase PWM Controller with 6-Bit DAC and Programmable Internal Temperature Compensation for VR10.X Application |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC32 |
| 封裝： | 5 X 5 MM, LEAD FREE, PLASTIC, MO-220VHHD-2, QFN-32 |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 692K |
| 代理商： | ISL6556BCRZ |
11
FN9097.4
December 28, 2004
Figures 14, 16 and 16 in the section entitled
Input Capacitor
Selection
can be used to determine the input-capacitor RMS
current based on load current, duty cycle, and the number of
channels. They are provided as aids in determining the
optimal input capacitor solution. Figure 17 shows the single
phase input-capacitor RMS current for comparison.
PWM Operation
The timing of each converter leg is set by the number of
active channels. The default channel setting for the
ISL6556B is four. One switching cycle is defined as the time
between PWM1 pulse termination signals. The pulse
termination signal is the internally generated clock signal
that triggers the falling edge of PWM1. The cycle time of the
pulse termination signal is the inverse of the switching
frequency set by the resistor between the FS pin and
ground. Each cycle begins when the clock signal commands
the channel-1 PWM output to go low. The PWM1 transition
signals the channel-1 MOSFET driver to turn off the
channel-1 upper MOSFET and turn on the channel-1
synchronous MOSFET. In the default channel configuration,
the PWM2 pulse terminates 1/4 of a cycle after PWM1. The
PWM3 output follows another 1/4 of a cycle after PWM2.
PWM4 terminates another 1/4 of a cycle after PWM3.
If PWM3 is connected to VCC, two channel operation is
selected and the PWM2 pulse terminates 1/2 of a cycle later.
Connecting PWM4 to VCC selects three channel operation
and the pulse-termination times are spaced in 1/3 cycle
increments.
Once a PWM signal transitions low, it is held low for a
minimum of 1/3 cycle. This forced off time is required to
ensure an accurate current sample. Current sensing is
described in the next section. After the forced off time
expires, the PWM output is enabled. The PWM output state
is driven by the position of the error amplifier output signal,
V
COMP
, minus the current correction signal relative to the
sawtooth ramp as illustrated in Figure 4. When the modified
V
COMP
voltage crosses the sawtooth ramp, the PWM output
transitions high. The MOSFET driver detects the change in
state of the PWM signal and turns off the synchronous
MOSFET and turns on the upper MOSFET. The PWM signal
will remain high until the pulse termination signal marks the
beginning of the next cycle by triggering the PWM signal low.
Current Sensing
During the forced off time following a PWM transition low, the
controller senses channel current by sampling the voltage
across the lower MOSFET r
DS(ON)
(see Figure 3). A ground-
referenced operational amplifier, internal to the ISL6556B, is
connected to the PHASE node through a resistor, R
ISEN
.
The voltage across R
ISEN
is equivalent to the voltage drop
across the r
DS(ON)
of the lower MOSFET while it is
conducting. The resulting current into the ISEN pin is
proportional to the channel current, I
L
. The ISEN current is
sampled and held after sufficient settling time every
switching cycle. The sampled current, I
n
, is used for channel-
current balance, load-line regulation, overcurrent protection,
and module current sharing. From Figure 3, the following
equation for I
n
is derived
where I
L
is the channel current.
If R
DS(ON)
sensing is not desired, an independent current-
sense resistor in series with the lower MOSFET source can
serve as a sense element. The circuitry shown in Figure 3
represents channel n of an N-channel converter. This
circuitry is repeated for each channel in the converter, but
may not be active depending upon the status of the PWM3
and PWM4 pins as described under
PWM Operation
section.
Channel-Current Balance
The sampled current, I
n
, from each active channel is used to
gauge both overall load current and the relative channel
current carried in each leg of the converter. The individual
sample currents are summed and divided by the number of
active channels. The resulting average current, I
AVG
,
provides a measure of the total load current demand on the
converter and the appropriate level of channel current. Using
Figures 3 and 4, the average current is defined as
where N is the number of active channels and I
OUT
is the
total load current.
The average current is subtracted from the individual
channel sample currents. The resulting error current, I
ER
, is
filtered to modify V
COMP
. The modified V
COMP
signal is
compared to a sawtooth ramp signal to produce a modified
I
n
I
L
r
ISEN
)
-R
=
(EQ. 3)
FIGURE 3. INTERNAL AND EXTERNAL CURRENT-SENSING
CIRCUITRY
I
n
ISEN
IL
(
)
rRISEN
=
-
+
ISEN(n)
R
ISEN
SAMPLE
&
HOLD
ISL6556B INTERNAL CIRCUIT
EXTERNAL CIRCUIT
V
IN
CHANNEL N
UPPER MOSFET
CHANNEL N
LOWER MOSFET
-
+
ILrDS ON
(
)
I
L
(EQ. 4)
I
AVG
I
-----------------------------+
I
…
I
N
+
+
N
=
I
AVG
I
-----N
r
ISEN
)
-R
=
ISL6556B
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6556B | Optimized Multi-Phase PWM Controller with 6-Bit DAC and Programmable Internal Temperature Compensation for VR10.X Application |
| ISL6556BCB | PWM Controller with Wide Input Range 8-SOIC -40 to 125 |
| ISL6556BCB-T | Optimized Multi-Phase PWM Controller with 6-Bit DAC and Programmable Internal Temperature Compensation for VR10.X Application |
| ISL6556BCBZ-T | Optimized Multi-Phase PWM Controller with 6-Bit DAC and Programmable Internal Temperature Compensation for VR10.X Application |
| ISL6557ACB-T | Multi-Phase PWM Controller for Core-Voltage Regulation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6556BCRZA | 功能描述:IC CTRLR MULTIPHASE VRM10 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6556BCRZA-T | 功能描述:IC CTRLR MULTIPHASE VRM10 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6556BCRZ-T | 功能描述:IC CTRLR MULTIPHASE VRM10 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6557 WAF | 制造商:Intersil Corporation 功能描述: |
| ISL6557ACB | 功能描述:IC REG CTRLR BUCK PWM VM 24-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。