- 您現在的位置：買賣IC網 > PDF目錄383157 > ISL6563CR (INTERSIL CORP) Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers PDF資料下載
參數資料
| 型號： | ISL6563CR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| 中文描述： | SWITCHING CONTROLLER, 255 kHz SWITCHING FREQ-MAX, PQCC24 |
| 封裝： | 4 X 4 MM, PLASTIC, MO-220-VGGD-2, QFN-24 |
| 文件頁數： | 18/19頁 |
| 文件大?。?/td> | 516K |
| 代理商： | ISL6563CR |
18
FN9126.6
April 13, 2005
with lower ESR available in larger case sizes. However, the
equivalent series inductance (ESL) of these capacitors
increases with case size and can reduce the usefulness of the
capacitor to high slew-rate transient loading. Unfortunately,
ESL is not a specified parameter. Consult the capacitor
manufacturer and/or measure the capacitor’s impedance with
frequency to help select a suitable component.
Output Inductor Selection
One of the parameters limiting the converter’s response to a
load transient is the time required to change the inductor
current. In a multiphase converter, small inductors reduce
the response time with less impact to the total output ripple
current (as compared to single-phase converters).
The output inductor of each power channel controls the
ripple current. The control IC is stable for channel ripple
current (peak-to-peak) up to twice the average current. A
single channel’s ripple current is approximated by:
The current from multiple channels tend to cancel each other
and reduce the total ripple current. The total output ripple
current can be determined using the curve in Figure 10; it
provides the total ripple current as a function of duty cycle
and number of active channels, normalized to the parameter
K
NORM
at zero duty cycle.
V
SW
where L is the channel inductor value.
Find the intersection of the active channel curve and duty
cycle for your particular application. The resulting ripple
current multiplier from the y-axis is then multiplied by the
normalization factor, K
NORM
, to determine the total output
ripple current for the given application.
I
TOTAL
K
NORM
K
CM
=
Input Capacitor Selection
The important parameters for the bulk input capacitors are
the voltage rating and the RMS current rating. For reliable
operation, select bulk input capacitors with voltage and
current ratings above the maximum input voltage and
largest RMS current required by the circuit. The capacitor
voltage rating should be at least 1.25 times greater than the
maximum input voltage. The input RMS current required for
a multiphase converter can be approximated with the aid of
Figure 11.
As the input capacitors are responsible for sourcing the AC
component of the input current flowing into the upper
MOSFETs, their RMS current capacity must be sufficient to
handle the AC component of the current drawn by the upper
MOSFETs. Figure 11 can be used to determine the input-
capacitor RMS current function of duty cycle, maximum
sustained output current (I
O
), and the ratio of the peak-to-
peak inductor current (I
L,PP
) to the maximum sustained load
current, I
O
. Figure 11 can also be used as a reference
demonstrating the dramatic reduction in input capacitor RMS
current in a 2-phase DC/DC converter, as compared to a
single-phase regulator.
Use a mix of input bypass capacitors to control the input
voltage ripple. Use ceramic capacitance for the high
frequency decoupling and bulk capacitors to supply the
RMS current. Minimize the connection path inductance of
the high frequency decoupling ceramic capacitors (from
drain of upper MOSFET to source of lower MOSFET).
For bulk capacitance, several electrolytic or high-capacity MLC
capacitors may be needed. For surface mount designs, solid
tantalum capacitors can be used, but caution must be
exercised with regard to the capacitor surge current rating.
These capacitors must be capable of handling the surge-
current at power-up.
I
L PP
V
-------------------------------
V
–
SW
V
IN
---------------
×
=
K
NORM
L F
=
1.0
0.8
0.6
0.4
0.2
0
0
0.1
0.2
0.3
0.4
0.5
DUTY CYCLE (V
O
/V
IN
)
FIGURE 10. RIPPLE CURRENT vs DUTY CYCLE
C
C
0.3
0.1
0
0.2
I
R
/
O
)
FIGURE 11. NORMALIZED INPUT RMS CURRENT vs DUTY
CYCLE FOR A 2-PHASE CONVERTER
0
0.2
0.5
0.1
0.3
0.4
DUTY CYCLE (V
O
/V
IN
)
I
L,PP
= 0
I
L,PP
= 0.5 x I
O
I
L,PP
= 0.75 x I
O
ISL6563
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6563CRZ | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL6563IR | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL6563CR-T | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL6563EVAL1 | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
| ISL6563IRZ | Two-Phase Multi-Phase Buck PWM Controller with Integrated MOSFET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6563CR-T | 功能描述:IC CTRLR PWM MULTIPHASE 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6563CR-TK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6563CRZ | 功能描述:電流型 PWM 控制器 P6 TWO PHS CONT INTEGRTD DRVRS DESKT RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6563CRZ-T | 功能描述:電流型 PWM 控制器 P6 TWO PHS CONT INTEGRTD DRVRS DESKT RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6563CRZ-TK | 功能描述:IC CTRLR PWM MULTIPHASE 24-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。