參數資料
型號： ISL9208
廠商： Intersil Corporation
英文描述： Multi-Cell Li-ion Battery Pack OCP/Analog Front End(多節鋰離子電池組OCP/模擬前端)
中文描述： 多單元鋰離子電池OCP /模擬前端（多節鋰離子電池組OCP /模擬前端）
文件頁數： 18/28頁
文件大小： 504K
代理商： ISL9208
18
FN6446.1
November 2, 2007
WKUP Pin Operation
There are two ways to design a wake up of the ISL9208. In
an active LOW connection (WKPOL = “0” - default), the
device wakes up when a charger is connected to the pack.
This pulls the WKUP pin low when compared to a reference
based on the V
CELL1
voltage. In an active HIGH connection
(WKPOL = ‘1’) the device wakes up when the WKUP pin is
pulled high by a connection through an external switch.
Protection Functions
In the default recommended condition, the ISL9208
automatically responds to discharge overcurrent, discharge
short circuit, charge overcurrent, internal over-temperature,
and external over-temperature conditions. The designer can
set optional over-ride conditions that allow the response to
be dictated by the microcontroller. These are discussed
below.
OVERCURRENT SAFETY FUNCTIONS
The ISL9208 continually monitors the discharge current by
monitoring the voltage at the CSENSE and DSENSE pins. If
that voltage exceeds a selected value for a time exceeding a
selected delay, then the device enters an overcurrent or short
circuit protection mode. In these modes, the ISL9208
automatically turns off both power FETs and hence prevents
current from flowing through the terminals P+ and P-.
The voltage thresholds and the response times of the
overcurrent protection circuits are selectable for discharge
overcurrent, charge overcurrent, and discharge short circuit
conditions. The specific settings are determined by bits in
the Discharge Set Configuration Register (ADDR:05H)
on page 15, and the Charge/Time Scale Configuration Scale
Register (ADDR:06H) on page 16. In addition, refer to
“Registers” on page 12.
In an overcurrent condition, the ISL9208 automatically turns off
the voltage on CFET and DFET pins. The DFET output drives
the discharge FET gate low, turning off the FET quickly. The
CFET output turns off and allows the gate of the charge FET to
be pulled low through a resistor.
By turning off the FETs the ISL9208 prevents damage to the
battery pack caused by excessive current into or out of to the
cells (as in the case of a faulty charger or short circuit
condition).
When the ISL9208 detects a discharge overcurrent condition,
both power FETs are turned off and the DOC bit is set. (When
the FETs are turned off, the DFET and CFET bits are also
reset.) The automatic response to overcurrent during discharge
is prevented by setting the DENOCD bit to “1”. The external
microcontroller can turn on the FETs at any time to recover from
this condition, but it would usually turn on the load monitor
function (by setting the LDMONEN bit) and monitor the LDFAIL
bit to detect that the overcurrent condition has been removed.
When the ISL9208 detects a discharge short circuit condition,
both power FETs are turned off and DSC bit is set. (When the
FETs are turned off, the DFET and CFET bits are also reset.)
The automatic response to short circuit during discharge is
prevented by setting the DENSCD bit to “1”. The external
microcontroller can turn on the FETs at any time to recover from
this condition, but it would usually turn on the load monitor
function (by setting the LDMONEN bit) and monitor the LDFAIL
bit to detect that the overcurrent condition has been removed.
When the ISL9208 detects a charge overcurrent condition, both
power FETs are turned off and COC bit is set. (When the FETs
are turned off, the DFET and CFET bits are also reset.) The
automatic response to overcurrent during discharge is
prevented by setting the DENOCC bit to “1”. The external
microcontroller can turn on the FETs at any time to recover from
this condition, but it would usually wait to do this until the cell
voltages are not over charged and that the overcurrent
condition has been removed. Or, the microcontroller could wait
until the pack is removed from the charger and then
re-attached.
An alternative method of providing the protection function, if
desired by the designer, is to turn off the automatic safety
response. In this case, the ISL9208 devices still monitor the
conditions and set the status bits, but take no action in
overcurrent or short circuit conditions. Safety of the pack
depends, instead, on the microcontroller to send commands to
the ISL9208 to turn off the FETs.
To facilitate a microcontroller response to an overcurrent
condition, especially if the microcontroller is in a low power
state, a charge overcurrent flag (COC), a discharge overcurrent
flag (DOC), or the short circuit flag (DSC) being set causes the
ISL9208 TEMP3V output to turn on and pull high. (See
Figure 5.) This output can be used as an external interrupt by
the microcontroller to wake-up quickly to handle the overcurrent
condition.
ISL9208
FIGURE 3. WAKE UP CONTROL CIRCUITS
VSS
230k*
* Internal resistor
only connected when
WKPOL=1.
5V
WKUP
WKPOL
(CONTROL)
WKUP
(STATUS)
WAKE UP
CIRCUITS
V
CELL1
ISL9208
相關PDF資料
PDF描述
ISL9214 Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources
ISL9214RZ Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources
ISL9214RZ-T Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources
ISL9440 Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller
ISL9440A Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller
相關代理商/技術參數
參數描述
ISL9208_0711 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Multi-Cell Li-ion Battery Pack OCP/Analog Front End
ISL9208EVAL1Z 制造商:Intersil Corporation 功能描述:ISL9208 EVALUATION BOARD 1 - ROHS COMPLIANT - QFN - Bulk
ISL9208EVAL2Z 功能描述:EVAL BOARD 2 FOR ISL9208 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板
ISL9208IRZ 功能描述:IC MULTI-CELL LI-ION PROT 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2
ISL9208IRZ-T 功能描述:IC MULTI-CELL LI-ION PROT 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*