- 您現在的位置：買賣IC網 > PDF目錄383182 > ISL9208 (Intersil Corporation) Multi-Cell Li-ion Battery Pack OCP/Analog Front End(多節鋰離子電池組OCP/模擬前端) PDF資料下載
參數資料
| 型號： | ISL9208 |
| 廠商： | Intersil Corporation |
| 英文描述： | Multi-Cell Li-ion Battery Pack OCP/Analog Front End(多節鋰離子電池組OCP/模擬前端) |
| 中文描述： | 多單元鋰離子電池OCP /模擬前端（多節鋰離子電池組OCP /模擬前端） |
| 文件頁數： | 22/28頁 |
| 文件大?。?/td> | 504K |
| 代理商： | ISL9208 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
22
FN6446.1
November 2, 2007
User Flags
The ISL9208 contains four flags in the register area that the
microcontroller can use for general purpose indicators.
These bits are designated UFLG3, UFLG2, UFLG1, and
UFLG0. The microcontroller can set or reset these bits by
writing into the appropriate register.
The user flag bits are battery backed up, so the contents
remain even after exiting a sleep mode. However, if the
microcontroller sets the POR bit to force a power on reset, all
of the user flags will also be reset. In addition, if the voltage
on cell1 ever drops below the POR voltage, the contents of
the user flags (as well as all other register values) could be
lost.
Serial Interface
INTERFACE CONVENTIONS
The device supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter, and the receiving device as the
receiver. The device controlling the transfer is called the
master and the device being controlled is called the slave.
The master always initiates data transfers, and provides the
clock for both transmit and receive operations. Therefore,
the ISL9208 devices operate as slaves in all applications.
When sending or receiving data, the convention is the most
significant bit (MSB) is sent first. So, the first address bit sent
is bit 7.
CLOCK AND DATA
Data states on the SDA line can change only while SCL is
LOW. SDA state changes during SCL HIGH are reserved for
indicating start and stop conditions. See Figure 9.
START CONDITION
All commands are preceded by the start condition, which is a
HIGH to LOW transition of SDA when SCL is HIGH. The
device continuously monitors the SDA and SCL lines for the
start condition and will not respond to any command until
this condition has been met. See Figure 10.
STOP CONDITION
All communications must be terminated by a stop condition,
which is a LOW to HIGH transition of SDA when SCL is
HIGH. The stop condition is also used to place the device
into the Standby power mode after a read sequence. A stop
condition is only issued after the transmitting device has
released the bus. See Figure 10.
ACKNOWLEDGE
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, releases the bus after transmitting eight
bits. During the ninth clock cycle, the receiver pulls the SDA
line LOW to acknowledge that it received the eight bits of
data. See Figure 11.
The device responds with an acknowledge after recognition
of a start condition and the correct slave byte. If a write
operation is selected, the device responds with an
acknowledge after the receipt of each subsequent eight bits.
The device acknowledges all incoming data and address
bytes, except for the slave byte when the contents do not
match the device’s internal slave address.
In the read mode, the device transmits eight bits of data,
releases the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no stop
condition is generated by the master, the device will
continues to transmit data. The device terminates further
data transmissions if an acknowledge is not detected. The
master must then issue a stop condition to return the device
to Standby mode and place the device into a known state
.
SCL
SDA
DATA
STABLE
DATA
CHANGE
DATA
STABLE
FIGURE 9. VALID DATA CHANGES ON I
2
C BUS
SCL
SDA
START
STOP
FIGURE 10. I
2
C START AND STOP BITS
8
1
9
DATA OUTPUT
FROM
TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
ACKNOWLEDGE
FIGURE 11. ACKNOWLEDGE RESPONSE FROM
RECEIVER
SCL FROM
MASTER
ISL9208
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9214 | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL9214RZ | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL9214RZ-T | Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL9440 | Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller |
| ISL9440A | Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9208_0711 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Multi-Cell Li-ion Battery Pack OCP/Analog Front End |
| ISL9208EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL9208 EVALUATION BOARD 1 - ROHS COMPLIANT - QFN - Bulk |
| ISL9208EVAL2Z | 功能描述:EVAL BOARD 2 FOR ISL9208 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL9208IRZ | 功能描述:IC MULTI-CELL LI-ION PROT 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ISL9208IRZ-T | 功能描述:IC MULTI-CELL LI-ION PROT 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。