with its associated" />
參數資料
型號: ISL95810WIU8Z-T
廠商: Intersil
文件頁數: 12/13頁
文件大?。?/td> 0K
描述: IC XDCP 256-TAP 10KOHM 8-MSOP
標準包裝: 2,500
系列: XDCP™
接片: 256
電阻(歐姆): 10k
電路數: 1
溫度系數: 標準值 ±45 ppm/°C
存儲器類型: 非易失
接口: I²C
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-MSOP
包裝: 帶卷 (TR)
8
FN8090.2
September 19, 2006
Principles of Operation
The ISL95810 is an integrated circuit incorporating one DCP
with its associated registers, non-volatile memory, and a I2C
serial interface providing direct communication between a
host and the potentiometer and memory.
DCP Description
The DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of the
DCP are equivalent to the fixed terminals of a mechanical
potentiometer (RH and RL pins). The RW pin of the DCP is
connected to intermediate nodes, and is equivalent to the
wiper terminal of a mechanical potentiometer. The position
of the wiper terminal within the DCP is controlled by an 8-bit
volatile Wiper Register (WR). The DCP has its own WR.
When the WR of the DCP contains all zeroes (WR<7:0>:
00h), its wiper terminal (RW) is closest to its “Low” terminal
(RL). When the WR of the DCP contains all ones (WR<7:0>:
FFh), its wiper terminal (RW) is closest to its “High” terminal
(RH). As the value of the WR increases from all zeroes (00h)
to all ones (255 decimal), the wiper moves monotonically
from the position closest to RL to the closest to RH. At the
same time, the resistance between RW and RL increases
monotonically, while the resistance between RH and RW
decreases monotonically.
While the ISL95810 is being powered up, The WR is reset to
80h (128 decimal), which locates RW roughly at the center
between RL and RH. Soon after the power supply voltage
becomes large enough for reliable non-volatile memory
reading, the ISL95810 reads the value stored in non-volatile
Initial Value Registers (IVRs) and loads it into the WR.
The WR and IVR can be read or written directly using the
I2C serial interface as described in the following sections.
Memory Description
The ISL95810 volatile and non-volatile registers are
accessed by I2C interface operations at addresses 0 and 2
decimal. The non-volatile byte at addresses 0 contains the
initial value loaded at power-up into the volatile Wiper
Register (WR) of the DCP. The byte at address 1 is
reserved; the user should not write to it, and its value should
be ignored if read.
The volatile WR, and the non-volatile Initial Value Register
(IVR) of the DCP are accessed with the same Address Byte,
set to 00 hex in both cases.
A volatile byte at address 2 decimal, controls what byte is
read or written when accessing DCP registers: the WR, the
IVR, or both.
When the byte at address 2 is all zeroes, which is the default
at power-up:
A read operation to addresses 0 outputs the value of the
non-volatile IVR.
A write operation to addresses 0 writes the same value to
the WR and IVR of the corresponding DCP.
When the byte at address 2 is 80h (128 decimal):
A read operation to addresses 0 outputs the value of the
volatile WR.
A write operation to addresses 0 only writes to the
corresponding volatile WR.
It is not possible to write to an IVR without writing the same
value to its corresponding WR.
00h and 80h are the only values that should be written to
address 2. All other values are reserved and must not be
written to address 2.
FIGURE 13. MIDSCALE GLITCH, CODE 80h to 7Fh (WIPER 0)
FIGURE 14. LARGE SIGNAL SETTLING TIME
Typical Performance Curves (Continued)
Wiper Movement Mid Point
From 80h to 7fh
Signal at Wiper (Wiper Unloaded)
SCL
Signal at Wiper
(Wiper Unloaded Movement
From ffh to 00h)
ISL95810
相關PDF資料
PDF描述
MS3120F18-11S CONN RCPT 11POS WALL MNT W/SCKT
X9116WS8Z-2.7T1 IC XDCP 16-TAP 10K CMOS 8-SOIC
VI-2TF-MX-B1 CONVERTER MOD DC/DC 72V 75W
SY100E196JI IC DELAY LINE 7TAP 28-PLCC
ISL95811UFUZ-TK IC POT 256TAPS 5BYTES 8-MSOP
相關代理商/技術參數
參數描述
ISL95811UFRTZ 功能描述:IC POT 256TAPS 5BYTES 8-TDFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻(歐姆):100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行(芯片選擇,遞增,增/減) 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR)
ISL95811UFRTZ-TK 功能描述:IC POT 256TAPS 5BYTES 8-TDFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻(歐姆):10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN(2x3) 包裝:帶卷 (TR)
ISL95811UFUZ 功能描述:IC POT 256TAPS 5BYTES 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻(歐姆):10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN(2x3) 包裝:帶卷 (TR)
ISL95811UFUZ-T 功能描述:IC POT 256TAPS 5BYTES 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻(歐姆):10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN(2x3) 包裝:帶卷 (TR)
ISL95811UFUZ-TK 功能描述:IC POT 256TAPS 5BYTES 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻(歐姆):10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN(2x3) 包裝:帶卷 (TR)