- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1161 (NXP Semiconductors N.V.) Full-speed Universal Serial Bus single-chip host and device controller PDF資料下載
參數資料
| 型號： | ISP1161 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full-speed Universal Serial Bus single-chip host and device controller |
| 中文描述： | 全速通用串行總線的單芯片主機和設備控制器 |
| 文件頁數： | 41/127頁 |
| 文件大?。?/td> | 2762K |
| 代理商： | ISP1161 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁
Philips Semiconductors
ISP1161
Full-speed USB single-chip host and device controller
Product data
Rev. 01 — 3 July 2001
41 of 130
9397 750 08313
Philips Electronics N.V. 2001. All rights reserved.
With the device in a suspended state it will consume considerably less power by
turning off the internal 48 MHz clock, PLL and crystal, and setting the internal
regulator to power-down mode. The ISP1161 suspend and resume clock scheme is
shown in
Figure 37
.
Remark:
ISP1161 can be put into a fully suspended mode only after both the HC and
the DC go into the suspended mode, when the crystal can be turned off and the
internal regulator can be put into power-down mode.
Pin H_SUSPEND is the sensing output pin for HC’s suspended state. When the HC
goes into SUSPEND state, this pin will output a HIGH level (logic 1). This pin is
cleared to LOW (logic 0) level only when the HC is put into a RESET state or
OPERATIONAL state (refer to the HcControl register bits 7 to 6, 01H - Read, 81H -
Write). By setting bit 11, SuspendClkNotStop, of the HcHardwareConfiguration
register (20H - Read, A0H - Write), you can also define such that when the HC goes
into SUSPEND state, its internal clock is stopped or kept running. After HC enters the
SUSPEND State for 1.3 ms, the internal clock will be stopped if bit
SuspendClkNotStop is logic 0.
10.2 HC wakeup from suspended state
There are three methods to wake up the HC from the USB SUSPEND state:
hardware wakeup, software wakeup, and USB bus resume. They are described as
follows:
10.2.1
Wakeup by pin H_WAKEUP
Pins H_SUSPEND and H_WAKEUP provide hardware wakeup, a way of remote
wakeup control for the HC without the need to access the HC internal registers.
H_WAKEUP is an external wakeup control input pin for the HC. After the HC goes
into SUSPEND state, it can be woken up by sending a HIGH level pulse to pin
H_WAKEUP. This will turn on the HC’s internal clock, and set bit 6, ClkReady, of the
Hc
μ
PInterrupt register (24H - Read, A4H - Write). Under the SUSPEND state, once
pin H_WAKEUP goes HIGH, after 160
μ
s, the internal clock will be up. After the
internal clock is up, it will be kept running at least 1.14 ms depending on the status of
pin H_WAKEUP. If pin H_WAKEUP is HIGH, then the internal clock will be kept
running. If pin H_WAKEUP is LOW, then the internal clock can be kept running for
1.14 ms only, unless the microprocessor sets the HC into OPERATIONAL state
during this time.
10.2.2
Wakeup by pin CS (software wakeup)
During the SUSPEND state, an external microprocessor issues the chip select signal
through pin CS to ISP1161. This method of access to ISP1161 internal registers is a
software wakeup.
10.2.3
Wakeup by USB devices
For the USB bus resume, a USB device attached to the root hub port issues a
resume signal to the HC through the USB bus, switching the HC from SUSPEND
state to RESUME State. This will also set the ResumeDetected bit, bit 3 of the
HcInterruptStatus register (03H - Read, 83H - Write).
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1161A1 | Universal Serial Bus single-chip host and device controller |
| ISP1161A1BD | Universal Serial Bus single-chip host and device controller |
| ISP1161A1BM | Universal Serial Bus single-chip host and device controller |
| ISP1161BD | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161BM | Full-speed Universal Serial Bus single-chip host and device controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1161A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161A1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus single-chip host and device controller |
| ISP1161A1BD | 功能描述:IC USB HOST/DEVICE CTRLR 64-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| ISP1161A1BD,118 | 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1161A1BD,151 | 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。