參數資料
型號: ISP1181B
廠商: NXP Semiconductors N.V.
英文描述: Full-speed Universal Serial Bus peripheral controller
中文描述: 全速通用串行總線外設控制器
文件頁數: 26/70頁
文件大?。?/td> 341K
代理商: ISP1181B
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
26 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Remark:
If any change is made to an endpoint configuration which affects the
allocated memory (size, enable/disable), the FIFO memory contents of
all
endpoints
becomes invalid. Therefore, all valid data must be removed from enabled endpoints
before changing the configuration.
Code (Hex): 20 to 2F —
write (control OUT, control IN, endpoint 1 to 14)
Code (Hex): 30 to 3F —
read (control OUT, control IN, endpoint 1 to 14)
Transaction —
write/read 1 byte
12.1.2
Write/Read Device Address
This command is used to set the USB assigned address in the Address Register and
enable the USB device. The Address Register bit allocation is shown in
Table 16
.
A USB bus reset sets the device address to 00H (internally) and enables the device.
The value of the Address Register (accessible by the micro) is not altered by the bus
reset. In response to the standard USB request Set Address the firmware must issue
a Write Device Address command, followed by sending an empty packet to the host.
The
new
device address is activated when the host acknowledges the empty packet.
Code (Hex): B6/B7 —
write/read Address Register
Transaction —
write/read 1 byte
Table 14:
Bit
Symbol
Reset
Access
Endpoint Configuration Register: bit allocation
7
6
FIFOEN
EPDIR
0
0
R/W
R/W
5
4
3
2
1
0
DBLBUF
0
R/W
FFOISO
0
R/W
FFOSZ[3:0]
0
0
0
0
R/W
R/W
R/W
R/W
Table 15:
Bit
7
Endpoint Configuration Register: bit description
Symbol
Description
FIFOEN
A logic 1 indicates an enabled FIFO with allocated memory.
A logic 0 indicates a disabled FIFO (no bytes allocated).
EPDIR
This bit defines the endpoint direction (0 = OUT, 1 = IN). It also
determines the DMA transfer direction (0 = read, 1 = write).
DBLBUF
A logic 1 indicates that this endpoint has double buffering.
FFOISO
A logic 1 indicates an isochronous endpoint. A logic 0 indicates
a bulk or interrupt endpoint.
FFOSZ[3:0]
Selects the FIFO size according to
Table 5
6
5
4
3 to 0
Table 16:
Bit
Symbol
Reset
Access
Address Register: bit allocation
7
DEVEN
0
R/W
6
5
4
3
2
1
0
DEVADR[6:0]
0
R/W
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
相關PDF資料
PDF描述
ISP1181BBS Full-speed Universal Serial Bus peripheral controller
ISP1181BDGG Full-speed Universal Serial Bus peripheral controller
ISP1181 Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件)
ISP1181DGG INDUCTOR 4.7NH +-.3NH 0402 SMD
ISP1183 Low-power Universal Serial Bus interface device with DMA
相關代理商/技術參數
參數描述
ISP1181BBS 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB PERIPHERAL SMD 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN
ISP1181BBS,518 功能描述:USB 接口集成電路 USB 1.1 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181BBS,551 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181BBS,557 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181BBS518 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN