- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181B (NXP Semiconductors N.V.) Full-speed Universal Serial Bus peripheral controller PDF資料下載
參數資料
| 型號： | ISP1181B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full-speed Universal Serial Bus peripheral controller |
| 中文描述： | 全速通用串行總線外設控制器 |
| 文件頁數： | 41/70頁 |
| 文件大?。?/td> | 341K |
| 代理商： | ISP1181B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
41 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
13. Interrupts
Figure 8
shows the interrupt logic of the ISP1181B. Each of the indicated USB events
is logged in a status bit of the Interrupt Register. Corresponding bits in the Interrupt
Enable Register determine whether or not an event will generate an interrupt.
Interrupts can be masked globally by means of the INTENA bit of the Mode Register
(see
Table 19
).
The active level and signalling mode of the INT output is controlled by the INTPOL
and INTLVL bits of the Hardware Configuration Register (see
Table 21
). Default
settings after reset are active LOW and level mode. When pulse mode is selected, a
pulse of 166 ns is generated when the OR-ed combination of all interrupt bits
changes from logic 0 to logic 1.
8
7
EP0OUT
BUSTATUS
A logic 1 indicates the interrupt source: control OUT endpoint.
It monitors the current USB bus status (0 = awake,
1 = suspend).
A logic 1 indicates that an EOT interrupt has occurred for a short
packet.
A logic 1 indicates that an interrupt is issued every 1 ms
because of the Pseudo SOF; after 3 missed SOFs ‘suspend’
state is entered.
A logic 1 indicates that a SOF condition was detected.
A logic 1 indicates that an internal EOT condition was generated
by the DMA Counter reaching zero.
A logic 1 indicates that an ‘awake’ to ‘suspend’ change of state
was detected on the USB bus.
A logic 1 indicates that a ‘resume’ state was detected.
A logic 1 indicates that a bus reset condition was detected.
6
SP_EOT
5
PSOF
4
3
SOF
EOT
2
SUSPND
1
0
RESUME
RESET
Table 49:
Bit
Interrupt Register: bit description
…continued
Symbol
Description
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181BBS | Full-speed Universal Serial Bus peripheral controller |
| ISP1181BDGG | Full-speed Universal Serial Bus peripheral controller |
| ISP1181 | Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) |
| ISP1181DGG | INDUCTOR 4.7NH +-.3NH 0402 SMD |
| ISP1183 | Low-power Universal Serial Bus interface device with DMA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181BBS | 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB PERIPHERAL SMD 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN |
| ISP1181BBS,518 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS,551 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BBS518 | 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN |
發布緊急采購，3分鐘左右您將得到回復。