- 您現在的位置：買賣IC網 > PDF目錄373127 > KFG1G16Q2M-DIB5 (SAMSUNG SEMICONDUCTOR CO. LTD.) FLASH MEMORY(54MHz) PDF資料下載
參數資料
| 型號： | KFG1G16Q2M-DIB5 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | FLASH MEMORY(54MHz) |
| 中文描述： | 閃存（54MHz之間） |
| 文件頁數： | 117/125頁 |
| 文件大?。?/td> | 1657K |
| 代理商： | KFG1G16Q2M-DIB5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁當前第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
OneNAND1G(KFG1G16Q2M-DEB5)
FLASH MEMORY
117
OneNAND2G(KFH2G16Q2M-DEB5)
OneNAND4G(KFW4G16Q2M-DEB5)
From time-to-time supplemental technical information and application notes pertaining to the design and operation of the device in a
system are included in this section. Contact your Samsung Representative to determine if additional notes are available.
7.1 Methods of Determining Interrupt Status
There are two methods of determining Interrupt Status on the OneNAND. Using the INT pin or monitoring the Interrupt Status Regis-
ter Bit.
The OneNAND INT pin is an output pin function used to notify the Host when a command has been completed. This provides a hard-
ware method of signaling the completion of a program, erase, or load operation.
In its normal state, the INT pin is high if the INT polarity bit is default. Before a command is written to the command register, the INT
bit must be written to '0' so the INT pin transitions to a low state indicating start of the operation. Upon completion of the command
operation by the OneNAND’s internal controller, INT returns to a high state.
INT is an open drain output allowing multiple INT outputs to be Or-tied together. INT does not float to a hi-Z condition when the chip is
deselected or when outputs are disabled. Refer to section 2.8 for additional information about INT.
INT can be implemented by tying INT to a host GPIO or by continuous polling of the Interrupt status register.
7.1.1 The INT Pin to a Host General Purpose I/O
INT can be tied to a Host GPIO to detect the rising edge of INT, signaling the end of a command operation.
This can be configured to operate either synchronously or asynchronously as shown in the diagrams below.
INT
COMMAND
7.0 TECHNICAL AND APPLICATION NOTES
相關PDF資料 |
PDF描述 |
|---|---|
| KFH1G1612M-DED5 | FLASH MEMORY(54MHz) |
| KFH2G1612M-DED5 | FLASH MEMORY(54MHz) |
| KFH2G16D2M-DEB5 | FLASH MEMORY(54MHz) |
| KFH2G16D2M-DEB6 | FLASH MEMORY(54MHz) |
| KFH2G16D2M-DED5 | FLASH MEMORY(54MHz) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KFG1G16Q2M-DIB6 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FLASH MEMORY(54MHz) |
| KFG1G16Q2M-DID | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FLASH MEMORY |
| KFG1G16Q2M-DID5 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FLASH MEMORY(54MHz) |
| KFG1G16Q2M-DID6 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FLASH MEMORY(54MHz) |
| KFG1G16U2C-AIB6000 | 制造商:Samsung SDI 功能描述:NAND Flash Parallel/Serial 3.3V 1Gbit 64M x 16bit 76ns/70ns 63-Pin FBGA Tray |
發布緊急采購，3分鐘左右您將得到回復。