參數資料
型號： KITMPR121EVM
廠商： Freescale Semiconductor
文件頁數： 5/27頁
文件大?。?/td> 0K
描述： KIT EVALUATION MPR121
產品培訓模塊： MPR121: Low-Power Touch Sensor
標準包裝： 1
傳感器類型： 近程
接口： USB
電源電壓： 5V，USB
嵌入式： 否
已供物品： 4 個板，線纜，文檔
已用 IC / 零件： MPR121
產品目錄頁面： 2808 (CN2011-ZH PDF)
MPR121
Sensors
Freescale Semiconductor, Inc.
13
Noise Count Limit (NCL): Determines the number of samples consecutively greater than the Max Half Delta value. This is
necessary to determine that it is not noise. The range of the effective value is 0~255.
Filter Delay Count Limit (FDL): Determines the operation rate of the filter. A larger count limit means the filter delay is operating
more slowly. The range of the effective value is 0~255.
The setting of the filter is depended on the actual application. For more information on these registers, refer to application note
AN3891.
5.6
Touch / Release Threshold (0x41~0x5A)
ExTTH: Electrode touch threshold, in range of 0~0xFF.
ExRTH: Electrode release threshold, in range of 0~0xFF.
Each of the 13 channels can be set with its own set of touch and release thresholds. Touch and release are detected by
comparing the electrode filtered data to the baseline value. The amount of deviation from the baseline value represents a
immediate capacitance change detected by possible a touch/release action.
Touch condition: Baseline - Electrode filtered data > Touch threshold
Release condition: Baseline - Electrode filtered data < Release threshold
Threshold settings are dependant on the touch/release signal strength, system sensitivity and noise immunity requirements. In
a typical touch detection application, threshold is typically in the range 0x04~0x10. The touch threshold is several counts larger
than the release threshold. This is to provide hysteresis and to prevent noise and jitter. For more information, refer to the
application note AN3892 and the MPR121 design guidelines.
5.7
Debounce Register (0x5B)
DT: Debounce number for touch. The value range is 0~7.
DR: Debounce number for release. The value range is 0~7.
All 13 channels use the same set of touch and release debounce numbers. The status bits in Status Register 0x00 and 0x01 will
only take place after the number of consecutive touch or release detection meets the debounce number setting. The debounce
setting can be very useful in avoiding possible noise glitches. Using the debounce setting, the status bit change will have a delay
of {ESI x SFI x DR (or DT)}.
ELEx, ELEProx Touch Threshold (0x41,0x43,...,0x59)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
ExTTH
Write
ELEx, ELEProx Release Threshold (0x42,0x44,...,0x5A)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
ExRTH
Write
Debounce Register (0x5B)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
—
DR
—
DT
Write
相關PDF資料
PDF描述
22R473MC IND 47UH 0.99A DRUM 7.8X7.5 SMD
LB3218T331K INDUCTOR 330UH 10% 1207 SMD
SEK100M160ST CAP ALUM 10UF 160V 20% RADIAL
KITMPR03XEVM KIT EVAL FOR MPR03X
MIC4101YM IC MOSFET DVR HALF BRIDGE 8-SOIC
相關代理商/技術參數
參數描述
KITMPR121EVM 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit
KITMPVZ5004EVK 功能描述:壓力傳感器開發工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
KITMPXA6115AEVB 功能描述:壓力傳感器開發工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
KITMPXSHOWEVK 功能描述:壓力傳感器開發工具 PRESSURE SHOWBOARD RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
KITMPXV5004DPEVB 功能描述:壓力傳感器開發工具 MPXV5004 Dev Kit RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*