- 您現在的位置：買賣IC網 > PDF目錄3987 > KMPC8555VTAPF (Freescale Semiconductor)IC MPU POWERQUICC III 783-FCPBGA PDF資料下載
參數資料
| 型號： | KMPC8555VTAPF |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 80/88頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MPU POWERQUICC III 783-FCPBGA |
| 標準包裝： | 1 |
| 系列： | MPC85xx |
| 處理器類型： | 32-位 MPC85xx PowerQUICC III |
| 速度： | 833MHz |
| 電壓： | 1.2V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 783-BBGA，F(xiàn)CBGA |
| 供應商設備封裝： | 783-FCPBGA（29x29） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
MPC8555E PowerQUICC III Integrated Communications Processor Hardware Specification, Rev. 4.2
Freescale Semiconductor
81
System Design Information
17.6
Configuration Pin Multiplexing
The MPC8555E provides the user with power-on configuration options which can be set through the use
of external pull-up or pull-down resistors of 4.7 k
Ω on certain output pins (see customer visible
configuration pins). These pins are generally used as output only pins in normal operation.
While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins
while HRESET is asserted, is latched when HRESET deasserts, at which time the input receiver is disabled
and the I/O circuit takes on its normal function. Most of these sampled configuration pins are equipped
with an on-chip gated resistor of approximately 20 k
Ω. This value should permit the 4.7-kΩ resistor to pull
the configuration pin to a valid logic low level. The pull-up resistor is enabled only during HRESET (and
for platform/system clocks after HRESET deassertion to ensure capture of the reset value). When the input
receiver is disabled the pull-up is also, thus allowing functional operation of the pin as an output with
minimal signal quality or delay disruption. The default value for all configuration bits treated this way has
been encoded such that a high voltage level puts the device into the default state and external resistors are
needed only when non-default settings are required by the user.
Careful board layout with stubless connections to these pull-down resistors coupled with the large value
of the pull-down resistor should minimize the disruption of signal quality or speed for output pins thus
configured.
The platform PLL ratio and e500 PLL ratio configuration pins are not equipped with these default pull-up
devices.
17.7
Pull-Up Resistor Requirements
The MPC8555E requires high resistance pull-up resistors (10 k
Ω is recommended) on open drain type
pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in Figure 53. Care must be taken to ensure that these pins are maintained at a valid deasserted
state under normal operating conditions as most have asynchronous behavior and spurious assertion give
unpredictable results.
TSEC1_TXD[3:0] must not be pulled low during reset. Some PHY chips have internal pulldowns that
could cause this to happen. If such PHY chips are used, then a pullup must be placed on these signals strong
enough to restore these signals to a logical 1 during reset.
Refer to the PCI 2.2 specification for all pull-ups required for PCI.
17.8
JTAG Configuration Signals
Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the
IEEE 1149.1 specification, but is provided on all processors that implement the Power Architecture. The
device requires TRST to be asserted during reset conditions to ensure the JTAG boundary logic does not
interfere with normal chip operation. While it is possible to force the TAP controller to the reset state using
only the TCK and TMS signals, generally systems assert TRST during the power-on reset flow. Simply
tying TRST to HRESET is not practical because the JTAG interface is also used for accessing the common
on-chip processor (COP) function.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT70V3379S4BF | IC SRAM 576KBIT 4NS 208FBGA |
| KMPC8555VTALF | IC MPU POWERQUICC III 783-FCPBGA |
| XCS20XL-5TQ144C | IC FPGA 3.3V C-TEMP HP 144TQFP |
| 65801-053LF | CLINCHER RECEPTACLE ASSY GOLD |
| IDT70V3379S4BCG | IC SRAM 576KBIT 4NS 256BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KMPC8555VTAQF | 功能描述:IC MPU POWERQUICC III 783-FCPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC85xx 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA（25x25） 包裝:托盤 |
| KMPC855TCVR50D4 | 功能描述:微處理器 - MPU POWER QUICC-NO LEAD RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| KMPC855TCVR66D4 | 功能描述:微處理器 - MPU POWER QUICC-NO LEAD RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| KMPC855TCZQ50D4 | 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| KMPC855TCZQ66D4 | 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
發布緊急采購，3分鐘左右您將得到回復。