Micrel May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001 MICREL CONFIDENTIAL. DO NOT DISTRIBUTE. 12 Fu" />
參數資料
型號： KS8001S TR
廠商： Micrel Inc
文件頁數： 4/44頁
文件大小： 0K
描述： TXRX 10/100 LINKMD 3.3V 48-SSOP
標準包裝： 1,000
類型： 收發器
驅動器/接收器數： 1/1
規程： IEEE 802
電源電壓： 1.8 V ~ 3.3 V
安裝類型： 表面貼裝
封裝/外殼： 48-BSSOP（0.295"，7.50mm 寬）
供應商設備封裝： 48-SSOP
包裝： 帶卷 (TR)
配用： KS8001L-EVAL-ND - EVAL KIT EXPERIMENTAL KS8001L
其它名稱： KS8001STR
KS8001STR-ND
KS8001
Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
12
Functional Description
100BASE-TX Transmit
The 100BASE-TX transmit function performs parallel-to-serial conversion, NRZ to NRZI conversion, MLT-3 encoding and
transmission. The circuitry starts with a parallel-to-serial conversion, which converts the 25 MHz, 4-bit nibbles into a 125 MHz serial
bit stream. The incoming data is clocked in at the positive edge of the TXC signal. The serialized data is further converted from
NRZ to NRZI format, and then transmitted in MLT3 current output. The output current is set by an external 1% 6.65 K
resistor for
the 1:1 transformer ratio. It has typical rise/fall times of 4 ns and complies with the ANSI TP-PMD standard regarding amplitude
balance, overshoot and timing jitter. The wave-shaped 10BASE-T output driver is also incorporated into the 100BASE-TX driver.
100BASE-TX Receive
The 100BASE-TX receive function performs adaptive equalization, DC restoration, MLT-3 to NRZI conversion, data and clock
recovery, NRZI to NRZ conversion, and serial-to-parallel conversion. The receiving side starts with the equalization filter to
compensate for inter-symbol interference (ISI) over the twisted pair cable. Since the amplitude loss and phase distortion are a
function of the length of the cable, the equalizer has to adjust its characteristic to optimize performance. In this design, the variable
equalizer will make an initial estimation based upon comparisons of incoming signal strength against some known cable
characteristics, then tunes itself for optimization. This is an ongoing process and can self adjust against environmental changes
such as temperature variations.
The equalized signal then goes through a DC restoration and data conversion block. The DC restoration circuit is used to
compensate for the effects of base line wander and to improve the dynamic range. The differential data conversion circuit converts
the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125 MHz clock from the edges of the NRZI signal. This recovered clock is then used to
convert the NRZI signal into the NRZ format. Finally, the NRZ serial data is converted to 4-bit parallel 4B nibbles. A synchronized
25 MHz RXC is generated so that the 4B nibbles is clocked out at the negative edge of RCK25 and is valid for the receiver at the
positive edge. When no valid data is present, the clock recovery circuit is locked to the 25 M
Ηz reference clock and both TXC and
RXC clocks continue to run.
PLL Clock Synthesizer
The KS8001 generates 125 M
Ηz, 25 MΗz and 20 MΗz clocks for system timing. An internal crystal oscillator circuit provides the
reference clock for the synthesizer.
Scrambler/De-scrambler (100BASE-TX only)
The purpose of the scrambler is to spread the power spectrum of the signal in order to reduce EMI and baseline wander.
10BASE-T Transmit
When TXEN (transmit enable) goes high, data encoding and transmission will begin. The KS8001 will continue to encode and
transmit data as long as TXEN remains high. The data transmission will end when TXEN goes low. The last transition occurs at the
boundary of the bit cell if the last bit is zero, or at the center of the bit cell if the last bit is one. The output driver is incorporated into
the 100BASE- driver to allow transmission with the same magnetics. They are internally wave-shaped and pre-emphasized into
outputs with a typical 2.5 V amplitude. The harmonic contents are at least 27 dB below the fundamental when driven by an all-ones
Manchester-encoded signal.
10BASE-T Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and a PLL
performs the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data. A squelch
circuit rejects signals with levels less than 300 mV or with short pulse widths in order to prevent noises at the RX+ or RX- input from
falsely trigger the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming signal and the KS8001
decodes a data frame. This activates the carrier sense (CRS) ad RXDV signals and makes the receive data (RXD) available. The
receive clock is maintained active during idle periods in between data reception.
相關PDF資料
PDF描述
KS8001SI TXRX 10/100 LINKMD 3.3V 48-SSOP
KS8695PI IC ARM9 W/MMU 5PORT 289-PBGA
KS8695PX IC SWITCH 10/100 1PORT 289PBGA
KS8695X IC SWITCH 10/100 5PORT 208PQFP
KS8721BLI TR TXRX 10/100 3.3V 48-LQFP
相關代理商/技術參數
參數描述
KS800A500-1800V Y40KSEA 制造商:LIUJING 制造商全稱:LIUJING 功能描述:可控硅、晶閘管
KS800A500-1800V Y40KSE 制造商:LIUJING 制造商全稱:LIUJING 功能描述:可控硅、晶閘管
KS8081 功能描述:IC SWITCH 10/100 3PORT 128PQFP RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KS-80H 制造商:Taiyo Electric Ind. 功能描述:
KS-80R 制造商:Taiyo Electric Ind. 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*