- 您現在的位置：買賣IC網 > PDF目錄10144 > KSZ8001SL TR (Micrel Inc)TXRX 10/100 LINKMD 3.3V 48-SSOP PDF資料下載
參數資料
| 型號： | KSZ8001SL TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 15/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX 10/100 LINKMD 3.3V 48-SSOP |
| 標準包裝： | 1,000 |
| 類型： | 收發器 |
| 規程： | MII，RMII，SMII |
| 電源電壓： | 1.8V, 3.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-BSSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 48-SSOP |
| 包裝： | 帶卷 (TR) |
| 配用： | 576-1620-ND - BOARD EVALUATION FOR KSZ8001L |
| 其它名稱： | KSZ8001SLTR KSZ8001SLTR-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Micrel
KSZ8001
June 2009
Revision 1.04
22
Auto MDI/MDI-X Cross-Over Transformer Connection
KSZ8001 features HP Auto MDI/MDI-X crossover and requires symmetric transformers that support Auto MDI/MDI-X.
See
“Selection of Isolation Transformer” for a list of transformers that support Auto MDI/MDI-X.
Power Management
The KSZ8001 offers the following modes for power management:
Power Down Mode:
This mode can be achieved by writing to Register 0.11 or pulling pin 30 PD# Low. In the power down
state, the KS8061 disables all internal functions and drives output pins to logic zero, except for the MII serial management
interface.
Power Saving Mode:
writing to register 1fh.10 can disable this mode. The KSZ8001 will then turn off everything except for
the Energy Detect and PLL circuits when the cable is not installed. In other words, the KSZ8001 will shutdown most of the
internal circuits to save power if there is no link. Power Saving mode will be in this most effective state when Auto-
Negotiation Mode is enabled.
100BASE-FX Mode
100BASE-FX mode is activated when FXSD/FXEN is higher than 0.6V (This pin has a default pull down). Under this mode, the auto-
negotiation and auto-MDIX features are disabled.
In fiber operation FXSD pin should connect to the SD (signal detect) output of the fiber module. The internal threshold of FXSD is
around
Vdd +/- 50 mV (2.2V +/- 0.05V at 3.3V). Above this level, it is considered Fiber signal detected, and the operation is
summarized in the following table:
FXSD/FXEN
Condition
Less than 0.6V
100TX mode
Less than 2.15V,
but greater than 0.6V
FX mode
No signal detected
FEF generated
Greater than 2.25V
FX mode
Signal detected
To ensure proper operation, the swing of fiber module SD should cover the threshold variation. A resistive voltage divider is
recommended to adjust the SD voltage range.
FEF (Far End Fault), repetition of a special pattern, which consists of 84-ones and 1-zero, is generated under “FX mode with no
signal detected”. The purpose of FEF is to notify the sender of a faulty link. When receiving a FEF, the LINK will go down to indicate
a fault, even with fiber signal detected. The transmitter is not affected by receiving a FEF and still sends out its normal transmit
pattern from MAC. FEF can be disabled by strapping pin27 low, please refer to “Strapping Options” section.
Media Converter Operation
The KSZ8001 is capable of performing media conversion with 2 parts in a back-to-back RMII mode as indicated in the diagram. Both
parts are in RMII mode and with RMII_BTB asserted (pin21 & 22 strapped high). One part is operating at TX mode and the other in
FX mode. Both parts can share a common 50MHz oscillator.
Under this operation, auto-Negotiation on the TX side will prohibit 10BASE-T link up. Additional options can be implemented under
this operation. Disable the transmitter and set it at tri-state by controlling the high TXD2 pin. In order to do this, RXD2 and TXD2 pins
need to be connected via an inverter. When TXD2 pin is high in both the copper and fiber operation, it disables transmit. Meanwhile,
the RXD2 pin on the copper side serves as the energy detect and can indicate if a line signal is detected. TXD3 should be tied low
and RXD3 let float. Please contact your local Micrel FAE for a Media Converter reference design.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1606ISW#TR | IC ADC 16BIT 5V SAMPLING 28SOIC |
| IDT7202LA50TP | IC FIFO ASYNCH 1KX9 35NS 28DIP |
| KSZ8001L TR | TXRX 10/100 3.3V 48-LQFP |
| VE-2NT-MX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
| LTC2856HMS8-2#TRPBF | IC TXRX RS485/RS422 8-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ801S | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:1.8C, 3.3V 10/100BASE-T/TX/FX Physical Layer Transceiver |
| KSZ8021RNL | 功能描述:TXRX PHY 100BASE TX 3.3V 24QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| KSZ8021RNL TR | 功能描述:以太網 IC 3.3V, 100Base-FX Physical Layer Transceiver with RMII support (24-QFN) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8021RNL-EVAL | 功能描述:以太網開發工具 3.3V, 100Base-FX Physical Layer Transceiver w/ RMII Support - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8021RNL-TR | 功能描述:1/1 Transceiver Full RMII 24-QFN (4x4) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:過期 類型:收發器 協議:RMII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商器件封裝:24-QFN（4x4） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。