參數資料
型號： KSZ8001SL TR
廠商： Micrel Inc
文件頁數： 4/46頁
文件大?。?/td> 0K
描述： TXRX 10/100 LINKMD 3.3V 48-SSOP
標準包裝： 1,000
類型： 收發器
規程： MII，RMII，SMII
電源電壓： 1.8V, 3.3V
安裝類型： 表面貼裝
封裝/外殼： 48-BSSOP（0.295"，7.50mm 寬）
供應商設備封裝： 48-SSOP
包裝： 帶卷 (TR)
配用： 576-1620-ND - BOARD EVALUATION FOR KSZ8001L
其它名稱： KSZ8001SLTR
KSZ8001SLTR-ND
Micrel
KSZ8001
June 2009
Revision 1.04
12
Functional Description
100BASE-TX Transmit
The 100BASE-TX transmit function performs parallel-to-serial conversion, NRZ to NRZI conversion, MLT-3 encoding and
transmission. The circuitry starts with a parallel-to-serial conversion, which converts the 25 MHz, 4-bit nibbles into a 125 MHz serial
bit stream. The incoming data is clocked in at the positive edge of the TXC signal. The serialized data is further converted from
NRZ to NRZI format, and then transmitted in MLT3 current output. The output current is set by an external 1% 6.65 K
Ω resistor for
the 1:1 transformer ratio. It has typical rise/fall times of 4 ns and complies with the ANSI TP-PMD standard regarding amplitude
balance, overshoot and timing jitter. The wave-shaped 10BASE-T output driver is also incorporated into the 100BASE-TX driver.
100BASE-TX Receive
The 100BASE-TX receive function performs adaptive equalization, DC restoration, MLT-3 to NRZI conversion, data and clock
recovery, NRZI to NRZ conversion, and serial-to-parallel conversion. The receiving side starts with the equalization filter to
compensate for inter-symbol interference (ISI) over the twisted pair cable. Since the amplitude loss and phase distortion are a
function of the length of the cable, the equalizer has to adjust its characteristic to optimize performance. In this design, the variable
equalizer will make an initial estimation based upon comparisons of incoming signal strength against some known cable
characteristics, then tunes itself for optimization. This is an ongoing process and can self adjust against environmental changes
such as temperature variations.
The equalized signal then goes through a DC restoration and data conversion block. The DC restoration circuit is used to
compensate for the effects of base line wander and to improve the dynamic range. The differential data conversion circuit converts
the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125 MHz clock from the edges of the NRZI signal. This recovered clock is then used to
convert the NRZI signal into the NRZ format. Finally, the NRZ serial data is converted to 4-bit parallel 4B nibbles. A synchronized
25 MHz RXC is generated so that the 4B nibbles is clocked out at the negative edge of RCK25 and is valid for the receiver at the
positive edge. When no valid data is present, the clock recovery circuit is locked to the 25 M
Ηz reference clock and both TXC and
RXC clocks continue to run.
PLL Clock Synthesizer
The KSZ8001 generates 125 M
Ηz, 25 MΗz and 20 MΗz clocks for system timing. An internal crystal oscillator circuit provides the
reference clock for the synthesizer.
Scrambler/De-scrambler (100BASE-TX only)
The purpose of the scrambler is to spread the power spectrum of the signal in order to reduce EMI and baseline wander.
10BASE-T Transmit
When TXEN (transmit enable) goes high, data encoding and transmission will begin. The KSZ8001 will continue to encode and
transmit data as long as TXEN remains high. The data transmission will end when TXEN goes low. The last transition occurs at the
boundary of the bit cell if the last bit is zero, or at the center of the bit cell if the last bit is one. The output driver is incorporated into
the 100BASE- driver to allow transmission with the same magnetic. They are internally wave-shaped and pre-emphasized into
outputs with a typical 2.5 V amplitude. The harmonic contents are at least 27 dB below the fundamental when driven by an all-ones
Manchester-encoded signal.
10BASE-T Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and a PLL
performs the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data. A squelch
circuit rejects signals with levels less than 300 mV or with short pulse widths in order to prevent noises at the RX+ or RX- input from
falsely trigger the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming signal and the KSZ8001
decodes a data frame. This activates the carrier sense (CRS) ad RXDV signals and makes the receive data (RXD) available. The
receive clock is maintained active during idle periods in between data reception.
相關PDF資料
PDF描述
LTC1606ISW#TR IC ADC 16BIT 5V SAMPLING 28SOIC
IDT7202LA50TP IC FIFO ASYNCH 1KX9 35NS 28DIP
KSZ8001L TR TXRX 10/100 3.3V 48-LQFP
VE-2NT-MX-F2 CONVERTER MOD DC/DC 6.5V 75W
LTC2856HMS8-2#TRPBF IC TXRX RS485/RS422 8-MSOP
相關代理商/技術參數
參數描述
KSZ801S 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:1.8C, 3.3V 10/100BASE-T/TX/FX Physical Layer Transceiver
KSZ8021RNL 功能描述:TXRX PHY 100BASE TX 3.3V 24QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND
KSZ8021RNL TR 功能描述:以太網 IC 3.3V, 100Base-FX Physical Layer Transceiver with RMII support (24-QFN) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8021RNL-EVAL 功能描述:以太網開發工具 3.3V, 100Base-FX Physical Layer Transceiver w/ RMII Support - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8021RNL-TR 功能描述:1/1 Transceiver Full RMII 24-QFN (4x4) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:過期 類型:收發器 協議:RMII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商器件封裝:24-QFN（4x4） 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*