- 您現在的位置：買賣IC網 > PDF目錄10119 > KSZ8041FTLI TR (Micrel Inc)TXRX PHY 10/100 SGL LP 48TQFP PDF資料下載
參數資料
| 型號： | KSZ8041FTLI TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 13/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX PHY 10/100 SGL LP 48TQFP |
| 標準包裝： | 1,000 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | SMII |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
Micrel, Inc.
KSZ8041TL/FTL
April 2007
20
M9999-042707-1.1
MII Management (MIIM) Interface
The KSZ8041TL/FTL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface allows upper-layer devices to monitor and control the state of the
KSZ8041TL/FTL. An external device with MIIM capability is used to read the PHY status and/or configure the PHY
settings. Further detail on the MIIM interface can be found in Clause 22.2.4.5 of the IEEE 802.3u Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows an external controller
to communicate with one or more KSZ8041TL/FTL devices. Each KSZ8041TL/FTL device is assigned a PHY
address between 1 and 7 by the PHYAD[2:0] strapping pins.
An internal addressable set of thirteen 16-bit MDIO registers. Register [0:6] are required, and their functions are
defined by the IEEE 802.3u Specification. The additional registers are provided for expanded functionality.
The KSZ8041TL/FTL supports MIIM in MII mode, RMII mode and SMII mode.
The following table shows the MII Management frame format for the KSZ8041TL/FTL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
00AAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
00AAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 1. MII Management Frame Format
Interrupt (INTRP)
INTRP (pin 21) is an optional interrupt signal that is used to inform the external controller that there has been a status
update in the KSZ8041TL/FTL PHY register. Bits[15:8] of register 1Bh are the interrupt control bits, and are used to
enable and disable the conditions for asserting the INTRP signal. Bits[7:0] of register 1Bh are the interrupt status bits, and
are used to indicate which interrupt conditions have occurred. The interrupt status bits are cleared after reading register
1Bh.
Bit 9 of register 1Fh sets the interrupt level to active high or active low.
MII Data Interface
The Media Independent Interface (MII) is specified in Clause 22 of the IEEE 802.3u Specification. It provides a common
interface between physical layer and MAC layer devices, and has the following key characteristics:
Supports 10Mbps and 100Mbps data rates.
Uses a 25 MHz reference clock, sourced by the PHY.
Provides independent 4-bit wide (nibble) transmit and receive data paths.
Contains two distinct groups of signals: one for transmission and the other for reception.
By default, the KSZ8041TL/FTL is configured in MII mode after it is power-up or reset with the following:
A 25 MHz crystal connected to XI, XO (pins 15, 14), or an external 25MHz clock source (oscillator) connected to
XI.
CONFIG[2:0] (pins 27, 41, 40) set to ‘000’ (default setting).
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72421L25PF | IC FIFO 64X9 SYNC 25NS 32-TQFP |
| VI-2NM-MX-F2 | CONVERTER MOD DC/DC 10V 75W |
| VI-J4T-MX-S | CONVERTER MOD DC/DC 6.5V 75W |
| VI-2NM-MX-F1 | CONVERTER MOD DC/DC 10V 75W |
| LT1039CSW#TRPBF | IC DRIVR/RCVR TRPLE-RS232 18SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8041FTL-S | 功能描述:以太網 IC 10/100 PHY Fibre version and SMII RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041MLL | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII Support - Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041MLL TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII Support - Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041MLLI | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII support (Industrial grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041MLLI TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII support (Industrial grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。