- 您現在的位置：買賣IC網 > PDF目錄9692 > KSZ8051RNL (Micrel Inc)TXRX PHY 10/T100 3.3V RMII 32QFN PDF資料下載
參數資料
| 型號： | KSZ8051RNL |
| 廠商： | Micrel Inc |
| 文件頁數： | 21/59頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX PHY 10/T100 3.3V RMII 32QFN |
| 特色產品： | KSZ8051RNL Physical Layer Transceiver |
| 標準包裝： | 640 |
| 類型： | PHY 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RMII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 托盤 |
| 其它名稱： | 576-3713 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
Micrel, Inc.
KSZ8051MNL/RNL
July 2010
28
M9999-070910-1.0
RMII Back-to-Back Mode (KSZ8051RNL only)
In RMII Back-to-Back mode, a KSZ8051RNL interfaces with another KSZ8051RNL, or a KSZ8041FTL to provide a
complete 100Mbps copper repeater, or media converter solution, respectively.
The KSZ8051RNL devices are configured to RMII Back-to-Back mode after power-up or reset with the following:
Strapping pin CONFIG[2:0] (pins 18, 29, 28) set to ‘101’
A common 50MHz reference clock connected to XI (pin 9)
RMII signals connected as shown in the following table.
KSZ8051RNL (100Base-TX copper)
[Device 1]
KSZ8051RNL (100Base-TX copper)
[Device 2]
Pin Name
Pin Number
Pin Type
Pin Name
Pin Number
Pin Type
CRSDV
18
Output
TXEN
23
Input
RXD1
15
Output
TXD1
25
Input
RXD0
16
Output
TXD0
24
Input
TXEN
23
Input
CRSDV
18
Output
TXD1
25
Input
RXD1
15
Output
TXD0
24
Input
RXD0
16
Output
Table 4. RMII Signal Connection for RMII Back-to-Back Mode (100Base-TX Copper Repeater)
MII Management (MIIM) Interface
The KSZ8051MNL/RNL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface enables upper-layer device, like a MAC processor, to monitor and control the state
of the KSZ8051MNL/RNL. An external device with MIIM capability is used to read the PHY status and/or configure the
PHY settings. Further details on the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows the external controller
to communicate with one or more PHY devices.
A set of 16-bit MDIO registers. Registers [0:8] are standard registers, and their functions are defined per the IEEE
802.3 Specification. The additional registers are provided for expanded functionality. See “Register Map” section
for details.
As the default, the KSZ8051MNL/RNL supports unique PHY addresses 1 to 7, and broadcast PHY address 0. The latter is
defined per the IEEE 802.3 Specification, and can be used to read/write to a single KSZ8051MNL/RNL device, or write to
multiple KSZ8051MNL/RNL devices simultaneously.
Optionally, PHY address 0 can be disabled as the broadcast address by either hardware pin strapping (B-CAST_OFF, pin
19) or software (register 16h, bit 9), and assigned as a unique PHY address.
The PHYAD[2:0] strapping pins are used to assigned a unique PHY address between 0 and 7 to each KSZ8051MNL/RNL
device.
The following table shows the MII Management frame format for the KSZ8051MNL/RNL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
00AAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
00AAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 5. MII Management Frame Format – for KSZ8051MNL/RNL
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B4M-MW-F3 | CONVERTER MOD DC/DC 10V 100W |
| VE-J5T-MX-F3 | CONVERTER MOD DC/DC 6.5V 75W |
| VE-B1X-MW-F1 | CONVERTER MOD DC/DC 5.2V 100W |
| LT1785HN8#TRPBF | IC TXRX RS485/RS422 60V 8-DIP |
| VE-B1W-MW-F2 | CONVERTER MOD DC/DC 5.5V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8051RNL AM | 功能描述:以太網 IC Single-Port 10/100BT PHY (Automotive) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8051RNL AM TR | 功能描述:以太網 IC Single-Port 10/100BT PHY (Automotive) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8051RNL TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ RMII Support (32-QFN) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8051RNL-EVAL | 功能描述:以太網開發工具 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ RMII Support (32-QFN) - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8051RNLI | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:10Base-T/100Base-TX Physical Layer Transceiver |
發布緊急采購，3分鐘左右您將得到回復。