- 您現在的位置：買賣IC網 > PDF目錄30712 > L48DB12001PSA DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | L48DB12001PSA |
| 元件分類： | 電源模塊 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封裝： | QUARTER BRICK PACKAGE-7 |
| 文件頁數： | 3/13頁 |
| 文件大?。?/td> | 407K |
| 代理商： | L48DB12001PSA |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
DS_ L48DB12001 _02102009
11
THERMAL CONSIDERATIONS
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient
cooling of the power module is needed over the entire
temperature range of the module. Convection cooling is
usually the dominant mode of heat transfer.
Hence, the choice of equipment to characterize the thermal
performance of the power module is a wind tunnel.
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in heated
vertical
wind
tunnels
that
simulate
the
thermal
environments encountered in most electronics equipment.
This type of equipment commonly uses vertically mounted
circuit cards in cabinet racks in which the power modules
are mounted.
The following figure shows the wind tunnel characterization
setup. The power module is mounted on a test PWB and is
vertically positioned within the wind tunnel. The space
between the neighboring PWB and the top of the power
module is constantly kept at 6.35mm (0.25’’).
Thermal Derating
Heat can be removed by increasing airflow over the
module.To enhance system reliability, the power module
should always be operated below the maximum operating
temperature. If the temperature exceeds the maximum
module temperature, reliability of the unit may be affected.
Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)
12.7 (0.5”)
MODULE
AIR FLOW
50.8 (2.0”)
FACING PWB
PWB
AIR VELOCITY
AND AMBIENT
TEMPERATURE
MEASURED BELOW
THE MODULE
Figure 19:
Wind Tunnel Test Setup
THERMAL CURVES
Figure 20:
Temperature measurement location
* The allowed maximum hot spot temperature is defined at 119℃
L48DB12001(Standard) Output Current vs. Ambient Temperature and Air Velocity
@Vin = 48V (Either Orientation)
0.00
0.25
0.50
0.75
1.00
1.25
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Output Current(A)
Natural
Convection
Figure 21:
Output current vs. ambient temperature and air velocity
@Vin = 48V(Either Orientation)
相關PDF資料 |
PDF描述 |
|---|---|
| L4981BD | 2 A POWER FACTOR CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO20 |
| L4981B | 2 A POWER FACTOR CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDIP20 |
| L4981AD013TR | 2 A POWER FACTOR CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO20 |
| L5200-45-AH6-R | SWITCHED CAPACITOR REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PDSO6 |
| L5200-50-AG6-R | SWITCHED CAPACITOR REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L4-8R2-10 | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:FERRITE CHIP INDUCTORS |
| L4901 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DUAL 5V REGULATOR WITH RESET |
| L4901A | 功能描述:線性穩壓器 - 標準 Dual 5V 0.4A w/Reset RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| L4901AH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Positive Fixed Voltage Regulator |
| L4902A | 功能描述:線性穩壓器 - 標準 Dual 5V 0.3A w/Reset RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
發布緊急采購，3分鐘左右您將得到回復。