- 您現在的位置：買賣IC網 > PDF目錄43900 > L6599N (STMICROELECTRONICS) 0.8 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP16 PDF資料下載
參數資料
| 型號： | L6599N |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.8 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP16 |
| 封裝： | LEAD FREE, PLASTIC, DIP-16 |
| 文件頁數： | 32/36頁 |
| 文件大小： | 636K |
| 代理商： | L6599N |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁
L6599
Pin settings
5/36
N.
Name
Function
4RFmin
Minimum oscillator frequency setting. This pin provides a precise 2 V reference and a
resistor connected from this pin to GND defines a current that is used to set the minimum
oscillator frequency. To close the feedback loop that regulates the converter output voltage
by modulating the oscillator frequency, the phototransistor of an optocoupler will be
connected to this pin through a resistor. The value of this resistor will set the maximum
operating frequency. An R-C series connected from this pin to GND sets frequency shift at
start-up to prevent excessive energy inrush (soft-start).
5STBY
Burst-mode operation threshold. The pin senses some voltage related to the feedback
control, which is compared to an internal reference (1.25 V). If the voltage on the pin is lower
than the reference, the IC enters an idle state and its quiescent current is reduced. The chip
restarts switching as the voltage exceeds the reference by 50 mV. Soft-start is not invoked.
This function realizes burst-mode operation when the load falls below a level that can be
programmed by properly choosing the resistor connecting the optocoupler to pin RFmin (see
block diagram). Tie the pin to RFmin if burst-mode is not used.
6
ISEN
Current sense input. The pin senses the primary current though a sense resistor or a
capacitive divider for lossless sensing. This input is not intended for a cycle-by-cycle control;
hence the voltage signal must be filtered to get average current information. As the voltage
exceeds a 0.8 V threshold (with 50 mV hysteresis), the soft-start capacitor connected to pin
1 is internally discharged: the frequency increases hence limiting the power throughput.
Under output short circuit, this normally results in a nearly constant peak primary current.
This condition is allowed for a maximum time set at pin 2. If the current keeps on building up
despite this frequency increase, a second comparator referenced at 1.5 V latches the device
off and brings its consumption almost to a “before start-up” level. The information is latched
and it is necessary to recycle the supply voltage of the IC to enable it to restart: the latch is
removed as the voltage on the Vcc pin goes below the UVLO threshold. Tie the pin to GND if
the function is not used.
7LINE
Line sensing input. The pin is to be connected to the high-voltage input bus with a resistor
divider to perform either AC or DC (in systems with PFC) brownout protection. A voltage
below 1.25 V shuts down (not latched) the IC, lowers its consumption and discharges the
soft-start capacitor. IC’s operation is re-enabled (soft-started) as the voltage exceeds 1.25 V.
The comparator is provided with current hysteresis: an internal 15 A current generator is
ON as long as the voltage applied at the pin is below 1.25 V and is OFF if this value is
exceeded. Bypass the pin with a capacitor to GND to reduce noise pick-up. The voltage on
the pin is top-limited by an internal zener. Activating the zener causes the IC to shut down
(not latched). Bias the pin between 1.25 and 6 V if the function is not used.
8DIS
Latched device shutdown. Internally the pin connects a comparator that, when the voltage
on the pin exceeds 1.85 V, shuts the IC down and brings its consumption almost to a “before
start-up” level. The information is latched and it is necessary to recycle the supply voltage of
the IC to enable it to restart: the latch is removed as the voltage on the VCC pin goes below
the UVLO threshold. Tie the pin to GND if the function is not used.
9PFC_STOP
Open-drain ON/OFF control of PFC controller. This pin, normally open, is intended for
stopping the PFC controller, for protection purpose or during burst-mode operation. It goes
low when the IC is shut down by DIS > 1.85 V, ISEN > 1.5 V, LINE > 6 V and STBY < 1.25 V.
The pin is pulled low also when the voltage on pin DELAY exceeds 2V and goes back open
as the voltage falls below 0.3V. During UVLO, it is open. Leave the pin unconnected if not
used.
10
GND
Chip ground. Current return for both the low-side gate-drive current and the bias current of
the IC. All of the ground connections of the bias components should be tied to a track going
to this pin and kept separate from any pulsed current return.
Table 2.
Pin functions (continued)
相關PDF資料 |
PDF描述 |
|---|---|
| L6599TR | 0.8 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6610D | 6-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| L6610N | 6-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP24 |
| L6611DTRT | POWER SUPPLY SUPPORT CKT, PDSO20 |
| L6611D | 5-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6599NR | 功能描述:電壓模式 PWM 控制器 HV resonant CNTRL RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| L6599TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:High-voltage resonant controller |
| L65B | 制造商:Electro-Mech 功能描述: |
| L65B3C881-00000-000 | 制造商:Carling Technologies 功能描述:L-SERIES ROCKER SWITCH - Bulk |
| L65D1CNN1-00000-000 | 制造商:Carling Technologies 功能描述:L-SERIES ROCKER SWITCH - Bulk |
發布緊急采購，3分鐘左右您將得到回復。