- 您現在的位置：買賣IC網 > PDF目錄43900 > L6728AHTR (STMICROELECTRONICS) SWITCHING CONTROLLER, PDSO10 PDF資料下載
參數資料
| 型號： | L6728AHTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO10 |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, VFDFPN-10 |
| 文件頁數： | 16/33頁 |
| 文件大?。?/td> | 1033K |
| 代理商： | L6728AHTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
L6728AH
20 A demonstration board
Doc ID 15726 Rev 1
23/33
11.1
Demonstration board description
11.1.1
Power input (VIN)
This is the input voltage for the power conversion. The high-side drain is connected to this
input. This voltage can range from 1.5 V to 12 V bus.
If the voltage is between 5 V and 12 V it can supply also the device (through the VCC pin)
and in this case the R16 (0
Ω) resistor must be present.
11.1.2
Output (VOUT)
Different output voltage rails have been tested. For each rail a few component need to be
changed: these components are used to program the desiderated output voltage and to
compensate the system. The over-current-protection limit is set to ~27 A but it can be
changed by replacing the resistors R18.
Note:
All the previous resistors are SMD 0603 package, 1/16W, 1% tolerance.
11.1.3
Signal input (VCC)
Using the input voltage VIN to supply the controller no power is required at this input.
However the controller can be supplied separately from the power stage through the VCC
input and, in this case, the R16 (0
Ω) resistor must be unsoldered.
11.1.4
Test points
Several test points are provided to have easy access at all important signal characterizing
the device:
–
COMP: The output of the error amplifier;
–
FB: The inverting input of the error amplifier;
–
PGOOD: Signaling the regular functioning (active high);
–
VGDHS: The bootstrap diode anode;
–
PHASE: Phase node;
–
LGATE: Low-side gate pin of the device;
–
HGATE: High-side gate pin of the device.
Table 7.
Rail dependent components
Ref.
8 V rail
5 V rail
3.3 V rail
2.5 V rail
1.25 V rail
0.8 V rail
Q9
Mounted
Not mounted
R7
3.6 k
Ω
3.6 k
Ω
3.6 k
Ω
3.6 k
Ω
11 k
Ω
11 k
Ω
R6, R9
3.6 k
Ω
3.6 k
Ω
4.7 k
Ω
4.7 k
Ω
22 k
Ω
22 k
Ω
R8, R13
390
Ω
680
Ω
1.5 k
Ω
2.2 k
Ω
39 k
Ω
Open
相關PDF資料 |
PDF描述 |
|---|---|
| L6730DTR | 20 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| L6730D | 20 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| L6730CQTR | 20 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, QCC24 |
| L6730CTR | 20 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| L6730 | 20 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6728ATR | 功能描述:電壓模式 PWM 控制器 HIGH FREQ SINGLE PHASE PWM CNTRL RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| L6728D | 功能描述:電流型 PWM 控制器 SNGL PHASE PWM CONTROLLER RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| L6728DTR | 功能描述:電流型 PWM 控制器 Single-Phase PWM 5V to 12V Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| L6728H | 功能描述:電壓模式 PWM 控制器 Sgl Output 300 KHz DFN-10 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| L6728HTR | 功能描述:電流型 PWM 控制器 SINGLE PHASE PWM CNTRL PWR GOOD RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。