- 您現在的位置：買賣IC網 > PDF目錄367494 > L9312 Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications PDF資料下載
參數資料
| 型號： | L9312 |
| 英文描述： | Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| 中文描述： | 線路接口和線路接入電路轉發電池SLIC和振鈴繼電器的訓練班- 57應用 |
| 文件頁數： | 29/40頁 |
| 文件大?。?/td> | 709K |
| 代理商： | L9312 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Data Sheet
July 2001
Forward Battery SLIC and Ringing Relay for TR-57 Applications
L9312 Line Interface and Line Access Circuit
Agere Systems Inc.
29
Supervision
(continued)
Break-Before-Make Operation
To achieve break-before-make, use the logic control
sequence device switching as shown below.
Table 15. Break-Before-Make Logic Control
Sequence Device Switching
The advantage of break-before-make operation is that
it eliminates the current spike when the ring access
relay changes state. The disadvantage is that it forces
an all-off state. Under inductive ringing loads, due to
Ldi/dt effects, it may cause a reduction in the impulse
noise performance compared to make-before-break
switching.
Protection
External Protection
An external overvoltage clamp is required to ensure
that the off-state and on-state ratings of the solid-state
break switch and solid-state ring access switch are not
exceeded. The solid-state switches in the L9312 are
constructed in a dielectrically isolated high-voltage
technology. Because of the high device-to-device isola-
tion that is inherent in the dielectric isolation, only a tip
to ground and a ring to ground clamp is required. A tip
to ring overvoltage clamp is not needed. A foldback or
crowbar type device is recommended to minimize
power across the solid-state switches under a fault
condition.
The break switches and tip return switch are con-
structed from DMOS transistors. Because the on resis-
tance of the break switches is less than the tip side ring
return switch, the break switches are physically bigger
and have a higher current handling capability. Addition-
ally, the break switches have a foldback characteristic
that enables them to survive a higher on-state voltage
(320 V) than the tip ring return switch (130 V), which
does not have the foldback characteristic. (See On-
State Switch I-V Characteristics section.) The ring
access switch is a pnpn type device. Additionally, the
ring side will see the full power ring voltage, and the tip
side switch will see the power ringing voltage that is
attenuated by the ringing load, subscriber loop, feed
resistor, and protection resistors. Because of these dif-
ferences, the protection requirements on the tip side
are different from the protection requirements on the
ring side. Thus, it is recommended that an asymmetri-
cal (with respect to tip and ring) overvoltage protection
scheme be used.
Please contact your Agere Account Representative for
a recommended protection device.
Additionally, a series protection resistor with a fusible
characteristic or a PTC resistor is recommended to
limit current during lightning and power cross faults. A
minimum 50
is recommended in tip and ring.
The overall device protection is achieved through a
combination of the external overvoltage and overcur-
rent devices, along with the integrated thermal shut-
down feature, the integrated window comparator,
the break switch foldback characteristic, and the
dc/dynamic current-limit response of the break and tip
return switches.
Active Mode Response at PT/PR
The line break switches and tip return switch are cur-
rent-limited switches. The current-limit mechanism lim-
its current through the switch to the specified dc current
limit under low frequency or dc faults (power cross
and/or tip-ring to ground short) and limits the current to
the specified dynamic current-limit response under
transient faults, such as lightning.
During a lightning fault (typical 1000 V 10 x 700
μ
s
applied surge), the current-limited line break switches
will pass typically 2.5 A for 0.5
μ
s before forcing the
break switches off. Once in the off state, the external
protection device must ensure that the off-state voltage
rating of 320 V is not exceeded. Note that the maxi-
mum differential voltage is the positive zener rating of
the protection device less the battery voltage, which
will appear on the line feed side of the switch.
State
Break
Switches
closed
open
Ring
Switches
open
open
Comment
Active/Scan
Disconnect
(all-off)
Ring
Disconnect
(all-off)
Active/Scan
—
hold
>8 ms
—
hold
>8 ms
—
open
open
closed
open
closed
open
相關PDF資料 |
PDF描述 |
|---|---|
| L9313 | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| L9350 | Single Peripheral Driver |
| L9355 | Dual Peripheral Driver |
| L9500A | High-Voltage Ringing SLIC for VolP Applications |
| L9653M | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9313 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| L9324 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Peripheral Driver |
| L9326 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L-932P3C | 制造商:Kingbright Corporation 功能描述: |
| L-9331 | 制造商:Ideal Industries Inc 功能描述:L-9331 |
發布緊急采購，3分鐘左右您將得到回復。