- 您現在的位置：買賣IC網 > PDF目錄30716 > LA4160 2.2 W, 1 CHANNEL, AUDIO AMPLIFIER, PDIP14 PDF資料下載
參數資料
| 型號： | LA4160 |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 2.2 W, 1 CHANNEL, AUDIO AMPLIFIER, PDIP14 |
| 封裝： | HEAT SINK, DIP-14 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 224K |
| 代理商： | LA4160 |
LA4160
No.870-7/11
9
[Measures against oscillation]
Approximately
(Polyester film
capacitor)
Preamp.
0.01
μF
RL
1000pF
8
6
3. Power Amplifier
The power amplifier circuit consists of the differential stage (TR22, 23), predriver stage (TR41), driver stage (TR42,
44), and output stage (TR47,48). Bias resistor R36 of TR20 at the first stage is attached externally and the input
impedance depends on this R36. Input pin (4) whose potential is nearly equal to the ground potential can be connected
direct to the variable resistor without using an input coupling capacitor. The closed loop voltage gain is obtained by the
following equation.
VG (pwr) = 20 log
R19
R18
+ Rf
Since R19 = 20k
Ω, R18 = 50Ω are set, approximately 52dB max. is available if Rf = 0 is taken.
Proper Cares in Using IC
1. Printed Circuit Board
For the printed circuit board layout, refer to the printed circuit pattern example in principle. It is necessary that the
grounding points of the power amplifier input (variable resistor), pin (3) feedback resistor (Rf), and bias resistor
(R35) should be adjacent to one another. Especially, it should be noted that if a common impedance exists in the
variable resistor grounding, the distortion, residual ripple, and cross interference (leak of signal between
preamplifier and power amplifier) may worsen.
1
7
14
R1
R35
VR
To preamplifier
Make adjacent to one another.
8
LA4160
2. Oscillation
a) Preamplifier
Since oscillation may osccur when used at a low voltage
gain, a capacitor of approximately 10pF must be connected
across pins (8) and (6) for phase compensation. If the
capacitor connected across pins (8) and (6) has a large
capacitance at a low load impedance, further oscillation
may occur, and in this case the load pin must be grounded
through a capacitor of approximately 0.01
μF (Polyester
film capacitor). The input pin must be grounded through a capacitor of approximately 1000pF for the purpose of
prevention of radio disturbance and oscillation.
(
)
相關PDF資料 |
PDF描述 |
|---|---|
| LA4165M | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LA4166M | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LA4167M | SPECIALTY CONSUMER CIRCUIT, PDSO30 |
| LA4168M | SPECIALTY CONSUMER CIRCUIT, PDSO30 |
| LA4182 | 2.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA4162 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:SINGLE-CHIP AF AMPLIFIER |
| LA4165M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Recording/Playback IC for Micro-Cassette Tape Recorder |
| LA4166M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Recording and Playback System for Microcassette Players |
| LA4167M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1-Channel Record/Playback System for Microcassette and Cassette Recorders |
| LA4168 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Record/Playback System for Microcassette and Compact Cassette Recorders(148.50 k) |
發布緊急采購，3分鐘左右您將得到回復。