LA71586M
No.A0223-2/50
Electrical Characteristics at Ta = 25
°C, VCC = 5.0V
REC Mode Y
Ratings
Parameter
Symbol
In
Out
Conditions
min
typ
max
Unit
Current dissipation
(REC)
ICCR
Measure the sum of currents flowing into pins 40, 16,
58, 87, 75.
175
190
205
mA
EE Output level 1
(SW 1)
VEE1
T38A
T29
With VIN a 1Vp-p video signal (PAL), measure the
output level on T29.
2.00
2.10
2.20
Vp-p
EE Output level 2
(SW 2)
VEE2
T36A
T29
With VIN a 1Vp-p video signal (NTSC), measure the
output level on T29.
2.00
2.10
2.20
Vp-p
EE Output level 3
(SW 3)
VEE2
T34A
T29
With VIN a 1Vp-p video signal (NTSC), measure the
output level on T29.
2.00
2.10
2.20
Vp-p
AGC characteristics 1
AGC1
T38A
T29
With VIN a 2.0Vp-p video signal, measure the ratio of
the output level on T29 and VEE1.
0
0.6
1.2
dB
AGC characteristics 2
AGC2
T38A
T29
With VIN a 0.5Vp-p video signal, measure the ratio of
the output level on T29 and VEE1.
-1.2
-0.2
0.0
dB
AGC characteristics 3
AGC3
T38A
T29
With VIN a 700mVp-p luminance, 600mVp-p sync,
measure the sync level on T29.
550
650
750
mVp-p
AGC characteristics 4
AGC4
T38A
T29
With VIN a 700mVp-p luminance, 150mVp-p sync,
measure the sync level on T29.
330
380
430
mVp-p
Sync separator output
level
VSYR
T38A
T28
With VIN a 1.0Vp-p video signal, measure the output
pulse wave height on T28.
4.0
4.2
4.4
Vp-p
Sync separator output
pulse width
PWSYR
T38A
T28
With VIN a 1.0Vp-p video signal, measure the output
pulse width on T28.
4.4
4.7
5.0
s
Sync separator
threshold level
THSYR
T38A
T28
Gradually reduce the input level, and measure the
input level at the point that the output pulse width is
1
s or more wider than PWSYR.
-20
-15
dB
Sync tip level
Pedestal level
White level
LVOR
T38A
T29
With VIN a 1.0Vp-p video signal, measure the sync tip
and pedestal and white level on T29 video output,
and take these as LSYN LPED LWHT, respectively.
Quasi-V insertion level
VDR
T38A
T29
Measure the T29 DC voltage with 4.3V applied to
T27,and take this to be LVDR, and compute the
difference with LSYN measured above.
WHR = LSYN-LVDR
0
mV
Quasi-H insertion level
HDR
T38A
T29
Measure the T29 DC voltage with 3.6V applied to
T27, and take this to be LHDR, and compute the
difference with LPED measured above.
HDR = LPED-LHDR
-270
mV
White insertion level
WHR
T38A
T29
Measure the T29 DC voltage with 1.5V applied to
T26. and take this to be LWHR, and compute the
difference with LWHT measured above.
WHR = LWHT-LWHR
150
mV
Edge insertion level
EGR
T38A
T29
Measure the T29 DC voltage with 0.8V applied to
T26.and take this to be LEGR, and compute the
difference with LPED measured above.
EGR = LPED-LEGR
-300
mV
REC YNR operation
RYNR
T38A
T21
VIN=White 50%+CW (31.6mVp-p)
Measure the ratio of 32fH component and
32.5fH.
Serial
00: OFF
01: MIN
10: TYP
11: MAX
*
2
4
6
dB
Y LPF frequency
characteristics (1)
YLPF1
T38A
T21
With VIN a standard multi-burst signal (1Vp-p),
measure the 1MHz response to a 500kHz signal on
T21.
-0.6
-0.1
0.4
dB
Y LPF frequency
characteristics (2)
YLPF2
T38A
T21
With VIN a standard multi-burst signal (1Vp-p),
measure the 2MHz response to a 500kHz signal on
T21.
-1.3
-0.3
0.7
dB
Y LPF frequency
characteristics (3)
YLPF3
T38A
T21
With VIN a standard multi-burst signal (1Vp-p),
measure the 3MHz response to a 500kHz signal on
T21.
-4
-2
-0.5
dB
Y LPF frequency
characteristics (4)
YLPF4
T38A
T21
With VIN a standard multi-burst signal (1Vp-p)
measure the 4.43MHz response to a 500kHz signal
on T21.
-25
dB
Continued on next page.