參數資料
型號： LAN8187_06
廠商： SMSC Corporation
英文描述： 【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM
中文描述： 【15kV的ESD保護信息產業部/ RMII快速以太網PHY與HP Auto - MDIX功能和SMSC flexPWRTM
文件頁數： 15/72頁
文件大?。?/td> 433K
代理商： LAN8187_06
±15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR
TM
Datasheet
Revision 1.0 (12-14-06)
15
SMSC LAN8187/LAN8187I
DATASHEET
MODE2
I
PHY Operating Mode Bit 2:
set the default MODE of the PHY.
See
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on page 53
, for
the MODE options.
MODE1
I
PHY Operating Mode Bit 1:
set the default MODE of the PHY.
See
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on page 53
, for
the MODE options.
MODE0
I
PHY Operating Mode Bit 0:
set the default MODE of the PHY.
See
Section 5.4.9.2, "Mode Bus – MODE[2:0]," on page 53
, for
the MODE options.
REG_EN
I
Regulator Enable
: Internal +1.8V regulator enable:
VDDIO – Enables internal regulator.
VSS– Disables internal regulator.
AMDIX_EN
I
HP Auto-MDIX Enable:
This pin is used to manualy disable the
HP Auto-MDIX function. This can be bypassed using the internal
register 27 bit 15. Please see
Table 4.3, “Auto-MDIX Control,” on
page 30
for more information.
(VDDIO or Floating) – Enables HP Auto-MDIX.
VSS – Disables HP Auto-MDIX
CH_SELECT
I
Channel Select:
This pin is used in conjunction with the
AMDIX_EN pin above to manualy select the channel to transmit
and receive on. For more information please see
Table 4.3,
“Auto-MDIX Control,” on page 30
(VDDIO or Floating) – MDIX - TX pair receives RX pair transmits.
0V – MDI -TX pair transmits RX pair receives.
GPO0/RMII
I/O
General Purpose Output 0 –
General Purpose Output signal.
Driven by bits in registers 27 and 31.
RMII –
MII/RMII mode selection is latched on the rising edge of
the internal reset (nreset) based on the following strapping:
Float the GPO0 pin for MII mode or pull-high with an external
Pull-up resistor (see
Table 4.4, “Boot Strapping Configuration
Resistors,” on page 32
) to VDDIO to set the device in RMII
mode.
Note:
See
Section 4.6.3, "MII vs. RMII Configuration," on
page 26
for more details.
a.On nRST transition high, the PHY latches the state of the configuration pins in this table.
Table 3.5 General Signals
SIGNAL NAME
TYPE
DESCRIPTION
nINT
I/O
LAN Interrupt
– Active Low output. Place a pull-up external
resistor (see
Table 4.4, “Boot Strapping Configuration Resistors,”
on page 32
) to VCC 3.3V.
Notes:
This signal is mux’d with TX_ER/TXD4
See
Section 4.10, "(TX_ER/TXD4)/nINT Strapping," on
page 31
for additional details on Strapping options.
nRST
I
External Reset
– input of the system reset. This signal is active
LOW.
Table 3.4 Boot Strap Configuration Inputs
a
SIGNAL NAME
TYPE
DESCRIPTION
相關PDF資料
PDF描述
LAN8187 High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
LAN83C175 Ethernet CARDBUS Integrated Controller With Modem Support
LAN83C180 10/100 FAST ETHERNET PHY TRANSCEIVER
LAN83C185 HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER
LAN83C183-JD FAST ETHERNET PHYSICAL LAYER DEVICE
相關代理商/技術參數
參數描述
LAN8187I 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
LAN8187I-JT 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN8187-JT 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN83C171 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller
LAN83C171 WAF 制造商:SMSC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*