- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN8187_06 (SMSC Corporation) 【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM PDF資料下載
參數資料
| 型號： | LAN8187_06 |
| 廠商： | SMSC Corporation |
| 英文描述： | 【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM |
| 中文描述： | 【15kV的ESD保護信息產業部/ RMII快速以太網PHY與HP Auto - MDIX功能和SMSC flexPWRTM |
| 文件頁數： | 50/72頁 |
| 文件大?。?/td> | 433K |
| 代理商： | LAN8187_06 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
±15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR
TM
Datasheet
Revision 1.0 (12-14-06)
50
SMSC LAN8187/LAN8187I
DATASHEET
To set an interrupt, set the corresponding bit of the in the Mask Register 30, (see
Table 5.46
).
To Clear an interrupt, either clear the corresponding bit in the Mask Register (30), this will de-assert
the nINT output, or Clear the Interrupt Source, and write a ‘1’ to the corresponding Interrupt Source
Flag. Writing a ‘1’ to the Interrupt Source Flag will cause the state machine to check the Interrupt
Source to determine if the Interrupt Source Flag should clear or stay as a ‘1’. If the Condition to De-
Assert is true, then the Interrupt Source Flag is cleared, and the nINT is also de-asserted. If the
Condition to De-Assert is false, then the Interrupt Source Flag remains set, and the nINT remains
asserted.
Note:
The ENERGYON bit 17.1 is defaulted to a ‘1’ at the start of the signal acquisition process,
therefore the Interrupt source flag 29.7 will also read as a ‘1’ at power-up. If no signal is
present, then both 17.1 and 29.7 wil clear within a few milliseconds.
5.3.2.1
Example Alternative Interrupts system
For example 30.7 is set to ‘1’ to enable the ENERGYON interrupt. After a cable is plugged in,
ENERGYON (17.1) goes active and nINT will be asserted low.
To de-assert the nINT interrupt output, either.
1. Clear the ENERGYON bit (17.1), by removing the cable, then writing a ‘1’ to register 29.7.
Or
2. Clear the Mask bit 30.1
5.4
Miscellaneous Functions
5.4.1
Carrier Sense
The carrier sense is output on CRS. CRS is a signal defined by the MII specification in the IEEE 802.3u
standard. The PHY asserts CRS based only on receive activity whenever the PHY is either in repeater
mode or full-duplex mode. Otherwise the PHY asserts CRS based on either transmit or receive activity.
The carrier sense logic uses the encoded, unscrambled data to determine carrier activity status. It
activates carrier sense with the detection of 2 non-contiguous zeros within any 10 bit span. Carrier
sense terminates if a span of 10 consecutive ones is detected before a /J/K/ Start-of Stream Delimiter
pair. If an SSD pair is detected, carrier sense is asserted until either /T/R/ End–of-Stream Delimiter
pair or a pair of IDLE symbols is detected. Carrier is negated after the /T/ symbol or the first IDLE. If
/T/ is not followed by /R/, then carrier is maintained. Carrier is treated similarly for IDLE followed by
some non-IDLE symbol.
Table 5.46 Alternative Interrupt System Management Table.
Mask
Interrupt Source Flag
Interrupt Source
Event to Assert
nINT
Condition to
De-Assert.
Bit to Clear
nINT
30.7
29.7
ENERGYON
17.1
ENERGYON
Rising 17.1
17.1 low
29.7
30.6
29.6
Auto-Negotiation
complete
1.5
Auto-Negotiate
Complete
Rising 1.5
1.5 low
29.6
30.5
29.5
Remote Fault Detected
1.4
Remote Fault
Rising 1.4
1.4 low
29.5
30.4
29.4
Link Down
1.2
Link Status
Falling 1.2
1.2 high
29.4
30.3
29.3
Auto-Negotiation LP
Achnowledge
5.14
Acknowledge
Rising 5.14
5.14 low
29.3
30.2
29.2
Parallel Detection Fault
6.4
Parallel Detection
Fault
Rising 6.4
6.4 low
29.2
30.1
29.1
Auto-Negotiation Page
Received
6.1
Page Received
Rising 6.1
6.1 low
29.1
相關PDF資料 |
PDF描述 |
|---|---|
| LAN8187 | High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| LAN83C175 | Ethernet CARDBUS Integrated Controller With Modem Support |
| LAN83C180 | 10/100 FAST ETHERNET PHY TRANSCEIVER |
| LAN83C185 | HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER |
| LAN83C183-JD | FAST ETHERNET PHYSICAL LAYER DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN8187I | 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| LAN8187I-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN8187-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN83C171 | 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller |
| LAN83C171 WAF | 制造商:SMSC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。