參數資料
型號： LB11872H
元件分類： 運動控制電子
英文描述： BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO30
封裝： HSOP-28/30
文件頁數： 4/11頁
文件大?。?/td> 125K
代理商： LB11872H
LB11872H
No.7257-2/11
Allowable Operating Conditions at Ta = 25
°C
Parameter
Symbol
Conditions
Ratings
Unit
Supply voltage range
VCC
10 to 28
V
6.3 V regulator-voltage output current
IREG
0 to -20
mA
LD pin applied voltage
VLD
0 to 28
V
LD pin output current
ILD
0 to 15
mA
FGS pin applied voltage
VFG
0 to 28
V
FGS pin output current
IFG
0 to 10
mA
Electrical Characteristics at Ta
= 25°C, VCC = VM = 24V
Ratings
Parameter
Symbol
Conditions
min
typ
max
Unit
Supply current 1
ICC1
Stop mode
5
7
mA
Supply current 2
ICC2
Start mode
17
22
mA
Output saturation voltages VAGC = 3.5V
SOURCE (1)
VSAT1-1
IO = 0.5A, RF = 0Ω
1.7
2.2
V
SOURCE (2)
VSAT1-2
IO = 1.0A, RF = 0Ω
2.0
2.7
V
SINK (1)
VSAT2-1
IO = 0.5A, RF = 0Ω
0.4
0.9
V
SINK (2)
VSAT2-2
IO = 1.0A, RF = 0Ω
1.0
1.7
V
Output leakage current
IO (LEAK)
VCC = 28V
100
μA
6.3V Regulator-voltage output
Output voltage
VREG
5.90
6.25
6.60
V
Voltage regulation
ΔVREG1
VCC = 9.5 to 28V
50
100
mV
Load regulation
ΔVREG2
Iload = -5 to -20mA
10
60
mV
Temperature coefficient
ΔVREG3
Design target value*1
0
mV/
°C
Hall amplifier block
Input bias current
IB (HA)
Differential input : 50mVp-p
2
10
μA
Differential input voltage range
VHIN
SIN wave input
50
*600
mVp-p
Common-phase input voltage range
VICM
Differential input : 50mVp-p
2.0
VCC-2.5
V
Input offset voltage
VIOH
Design target value*1
-20
20
mV
FG amplifier and schmitt block (IN1)
Input amplifier gain
GFG
5
Times
Input hysteresis (high to low)
0
mV
Input hysteresis (low to high)
VSLH
-10
mV
Hysteresis width
VFGL
Input conversion
4
7
12
mV
Low-voltage protection circuit
Operating voltage
VSD
8.4
8.8
9.2
V
Hysteresis width
ΔVSD
0.2
0.4
0.6
V
Thermal protection circuit
Thermal shutdown operating
temperature
TSD
Design target value*1 (junction temperature)
150
180
°C
Hysteresis width
ΔTSD
Design target value*1 (junction temperature)
40
°C
Current limiter operation
Acceleration limit voltage
VRF1
0.53
0.59
0.65
V
Deceleration limit voltage
VRF2
0.32
0.37
0.42
V
Error amplifier
Input offset voltage
VIO (ER)
Design target value*1
-10
10
mV
Input bias current
IB (ER)
-1
1
μA
High-level output voltage
VOH (ER)
IOH = -500μA
VREG-1.2
VREG-0.9
V
Low-level output voltage
VOL (ER)
IOL = 500μA
0.9
1.2
V
DC bias level
VB (ER)
-5%
1/2VREG
5%
V
Note* : Since kickback can occur in the output waveform if the Hall input amplitude is too large, the Hall input. amplitudes should be held to under 350mVp-p.
*1 : This parameter is a design target value and is not measured.
Continued on next page.
相關PDF資料
PDF描述
LB11876 BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36
LB11889M BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO36
LB11946 STEPPER MOTOR CONTROLLER, 1.2 A, PDIP28
LB11946 STEPPER MOTOR CONTROLLER, 1.2 A, PDIP28
LB11980H BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO28
相關代理商/技術參數
參數描述
LB11872H_08 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Polygonal Mirror Motors Three-Phase Brushless Motor Driver
LB11872H-MPB-E 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
LB11872H-TLM-E 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
LB11872V 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC For Polygonal Mirror Motors Scanner Driver IC
LB11873 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC For Polygonal Mirror Motors Three-Phase Brushless Motor Driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*