- 您現在的位置：買賣IC網 > PDF目錄43902 > LB1870 (SANYO SEMICONDUCTOR CO LTD) BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP28 PDF資料下載
參數資料
| 型號： | LB1870 |
| 廠商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP28 |
| 封裝： | HSDIP-28 |
| 文件頁數： | 9/11頁 |
| 文件大小： | 108K |
| 代理商： | LB1870 |
External Component Values (reference values)
Note: Use a crystal that has a ratio of at least 1:5 between the fundamental f0 impedance and the 3f0 impedance.
Three Phase Logic Truth Table
Columns H1 to H3
H: H+ > H–
L: H+ < H–
Columns OUT1 to OUT3
H: Source
L: Sink
LB1870 Functional Description and External Components
1. Speed control circuit
This IC provides high-precision stable motor control with minimal jitter by adopting a PLL speed control scheme.
This PLL circuit compares the rising edge of the CLK signal with the falling edge of the FG Schmitt output and
outputs that phase error.
When an internal clock is used, the FG servo frequency is determined by the formula shown below. Thus the motor
speed is determined by the number of FG pulses and the crystal oscillator frequency.
fFG(servo) = fOSC/N
fOSC: Crystal oscillator frequency
N: Clock divisor
2. Three-phase full-wave current linear drive
This IC adopts a three-phase full-wave current linear drive to hold motor noise to an absolute minimum. When
switching the output transistor phase, it creates a two-phase excitation state, suppresses kickback, and smooths the
output waveform. This suppresses motor noise. Note that since oscillation may occur with some motors, the
capacitors C12, C13, and C14 (about 0.1
F) are connected between the OUT pins and ground.
3. Current limiter circuit
The current limiter circuit limits the current (i.e., the peak current) to a level determined by the formula I = 0.58/Rf.
A scheme in which the output stage drive current is limited is adopted for the limiting operation. Therefore, the phase
compensation capacitor C7 (about 0.1
F) is inserted between FC and ground.
4. Grounding
GND1 (pin 11 in the LB1870, pin 5 in the LB1870M) .........................................Output block ground (sub-ground)
GND2 (pin 28 in the LB1870, pins 1, 2, 17 to 20, 35, and 36 in the LB1870M)..Control circuit ground.
GND1 and GND2 should be connected on the circuit board by the shortest distance that occurs in the pattern. Also,
the Rf resistor R8 ground node and the GND1 and GND2 pattern line should be grounded to a single point on the
connector.
No. 4356-7/11
LB1870, 1870M
Crystal (MHz)
C1 (pF)
C2 (pF)
R (k)
3 to 4
39
82
0.82
4 to 5
39
82
1.0
5 to 7
39
47
1.5
7 to 10
39
27
2.0
H1
H2
H3
OUT1
OUT2
OUT3
HL
H
L
H
M
HL
LL
M
H
HH
L
M
LH
L
H
L
M
LH
H
M
L
LL
H
M
H
L
相關PDF資料 |
PDF描述 |
|---|---|
| LB1871 | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP28 |
| LB1876 | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDSO36 |
| LB1876 | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDSO36 |
| LB1921 | BRUSHLESS DC MOTOR CONTROLLER, 3.5 A, PDIP28 |
| LB1928 | BRUSHLESS DC MOTOR CONTROLLER, 3.1 A, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1870M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver |
| LB1871 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver |
| LB1871M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver |
| LB1872 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Polygon Mirror Scanner Driver IC |
| LB1875 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Polygon Mirror Motor Predriver IC |
發布緊急采購，3分鐘左右您將得到回復。