- 您現在的位置：買賣IC網 > PDF目錄358764 > LC75817NW (Sanyo Electric Co.,Ltd.) 1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function PDF資料下載
參數資料
| 型號： | LC75817NW |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | 1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function |
| 中文描述： | 1月8日至1月10日當值點陣液晶顯示控制器/輸入功能的關鍵驅動 |
| 文件頁數： | 23/43頁 |
| 文件大小： | 829K |
| 代理商： | LC75817NW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
No. 6144-23/43
LC75817E, 75817W
In sleep mode
The pins KS1 to KS6 are set to high or low with the “set key scan output state” instruction.
If a key on one of the lines corresponding to a KS1 to KS6 pin which is set high is pressed, the oscillator on the
OSCI, OSCO pins is started and a key scan is performed. Keys are scanned until all keys are released. Multiple key
presses are recognized by determining whether multiple key data bits are set.
If a key is pressed for longer than 4800T(s)(Where T= fosc
low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if CE
is high during a serial data transfer, DO will be set high.
After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75817E/W
performs another key scan. However, this dose not clear sleep mode. Also note that DO, being an open-drain output,
requires a pull-up resistor (between 1 and 10 k
).
Sleep mode key scan example
Example: When a “display on/off control (SP = 1)” instruction and a “set key scan output state (KC1 to KC5 = 0,
KC6 = 1)” instruction are executed (i.e. sleep mode with only KS6 high)
Multiple Key Presses
Although the LC75817E/W is capable of key scanning without inserting diodes for dual key presses, triple key presses on
the KI1 to KI5 input pin lines, or multiple key presses on the KS1 to KS6 output pin lines, multiple presses other than
these cases may result in keys that were not pressed recognized as having been pressed. Therefore, a diode must be
inserted in series with each key. Applications that do not recognize multiple key presses of three or more keys should
check the key data for three or more 1 bits and ignore such data.
Note:
*
19. These diodes are required to reliably recognize multiple key presses on the KS6 line when sleep mode state with only KS6 high, as in the above
example. That is, these diodes prevent incorrect operations due to sneak currents in the KS6 key scan output signal when keys on the KS1 to
KS5 lines are pressed at the same time.
“L” KS1
“L” KS2
“L” KS3
“L” KS4
“L” KS5
“H” KS6
KI1
KI2
KI3
KI4
KI5
When any one of these keys is pressed, the oscillator on the
OSCI, OSCO pins is started and the keys are scanned.
*
19
Key input
(KS6 line)
Key scan
CE
DI
DO
4800T(s)
4800T(s)
Serial data
transfer
Serial data
transfer
Key address
(43H)
Serial data
transfer
Key address
Key data read request
Key data read
Key data read request
T=
1
fosc
Key data read
相關PDF資料 |
PDF描述 |
|---|---|
| LC75821E | LCD Display Drivers |
| LC75822E | LCD Display Drivers |
| LC75823E | 1/3 Duty General-Purpose LCD Drivers |
| LC75824 | 1/4 Duty General-Purpose LCD Display Driver |
| LC75824W | 1/4 Duty General-Purpose LCD Display Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC75817W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/8 to 1/10 Duty Dot Matrix LCD Display Controller/Driver with Key Input Function |
| LC75818PT | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers with Key Input Function |
| LC7581E | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers |
| LC7581T | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1/8 to 1/10 Duty Dot Matrix LCD Display Controllers/Drivers |
| LC7582 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LCD Driver |
發布緊急采購，3分鐘左右您將得到回復。